Produktsökning

USB 3.0/eSATA hårddisk-dockningsstation med 6 fack och duplikator - 1:5 HDD/SSD-klonare och -raderare

Kopiera en 2,5 tums eller 3,5 tums SATA-enhet till fem hårddiskar samtidigt, eller docka källenheten eller de fem målenheterna till en dator via USB 3.0 eller eSATA

Produkt ID: SATDOCK5U3ER

  • Spara tid med 1:5 enhetsduplikation & massradering av 6 enheter
  • Problemfri fristående användning med inbyggd digital LCD-display
  • Maximera mångsidighet med eSATA- & USB 3.0-värdanslutningar, USB-portar endast för snabbladdning, plus dockningsstation, raderare och duplikator i en enda enhet
Ditt pris
€1 376,99 EUR excl. VAT
€1 721,24 EUR incl. VAT

SATDOCK5U3ER hårddiskduplikatorn & dockningsstationen låter dig klona en 2,5" eller 3,5" SATA-hårddisk (HDD) eller solid-state-enhet (SSD) till fem andra SATA-enheter samtidigt som en fristående enhet. Duplikatorn låter dig dessutom radera upp till 5 enheter utan en värdanslutning.

Du kan även använda duplikatorn som en HDD/SSD-dockningsstation med 5 fack genom att ansluta den till en värddator genom antingen USB 3.0 eller eSATA. Med stöd för enheter med hög kapacitet (testad med upp till 6 TB) är denna ett enkelt och kostnadseffektivt sätt att öka utrymmet för lagring/säkerhetskopiering.

Optimerad produktivitet

Genom att kopiera data från en enhet till fem enheter samtidigt förbättrar hårddiskklonaren din produktivitet genom att undvika bekymret med att hela tiden byta enheter vid stora dupliceringsprojekt.

Dessutom stöder dockningsstationen radering av upp till fem enheter samtidigt med flera driftslägen som till exempel snabbradering och multipass-överskrivning (DoD) - den idealiska lösningen för permanent radering av konfidentiell information och skyddar ditt företag och dina kunder från identitetsstöld.

Problemfri prestanda

Med en inbyggd LCD-display gör SATDOCK5U3ER det enkelt att övervaka dupliceringsförloppet och granska resultatet av kopiering/radering och enhetsdiagnostik vid fristående användning.

Även höljet har designats för att vara lättanvänt. Enhetsfacken har en design i dubbelprofil för problemfria byten mellan 2,5" och 3,5" hårddiskar och solid state-enheter utan att behöva använda extra fästen eller adaptrar.

Maximal mångsidighet

Med möjligheten att ansluta dockningsstationen genom antingen eSATA eller USB 3.0 är SATDOCK5U3ER en mångsidig lösning för att utöka lagringsutrymmet för nästan vilken bärbar eller stationär dator som helst. För snabb prestanda kan du ansluta dockningsstationen till datorn genom eSATA för effektiva dataöverföringshastigheter på upp till 3 Gbps. För bredare systemkompatibilitet kan du ansluta dockningsstationen genom USB 3.0 vilket dessutom är bakåtkompatibelt med USB 2.0/1.1-värdanslutningar.

SATDOCK5U3ER har dessutom två USB-portar endast för snabbladdning som du kan använda för att hålla din iPhone®, iPad® och dina Android™-surfplattor eller -smarttelefoner laddade. 

Du kan även duplicera, radera eller få åtkomst till andra enhetstyper vid duplicerings- och snabbraderingssituationer med en enhetsadapter. Följande StarTech.com-adaptrar har testats för att garantera kompatibilitet med denna enhetsduplikator:

SAT2IDEADP - SAT2IDEADP
SAT2MSAT25 - SAT2MSAT25
SAT32M225 - SAT32M225

SATDOCK5U3ER är byggd för pålitlig och långvarig prestanda, är hållbart tillverkad och täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Skapa flera exakta kopior av en källenhet till en ny enhet för stora antal identiska datorsystem
  • Gör exakta kopior av originalhårddiskar för testning eller undersökning inom brottsbekämpning och kriminalteknik
  • Snabb åtkomst till externa hårddiskar
  • Klona data för diskåterställning
  • Radera flera enheter säkert samtidigt för att skydda dig mot identitetsstöld

Fördelarna med StarTech.com

  • Maximal mångsidighet med HDD/SSD-duplikator, -dockningsstation och -raderare i en enda enhet
  • Spara tid på projekt med flera enhetsduplikationer genom att skapa fem duplicerade enheter samtidigt
  • Problemfri fristående användning och lättavläst övervakning av förlopp med inbyggd LCD-display

Partnernummer

  • Ingram Micro Sweden V933328
  • UPC 065030859172

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 19,7 cm [7,8 in]
Package Length 38,7 cm [15,2 in]
Fraktvikt (förpackning) 2,5 kg [5,5 lb]
Package Width 27,6 cm [10,9 in]
Hårdvara Antal enheter 5
Enhetsstorlek 2.5in & 3.5in
Enhetstyp SATA
2 - Flaktar 60 mm
Chipset-ID SunplusIT - SPIF260A
ASMedia - ASM1153
JMicron - JMB393
Indikatorer 1 - LED-indikatorer Dockningsstationens ström
Ström och aktivitet för källenhet
5 - LED-indikatorer Ström/aktivitet för målenhet
Kontakt(er) 6 - Enhetskontakter SATA data- & ström-kombo (7+15-stifts)
1 - Värdkontakter eSATA (7-stifts, data)
USB Type-B (9-stifts) USB 3.0
Miljö Drifttemperatur 5°C to 35°C (41°F to 95°F)
Förvaringstemperatur -20°C to 50°C (-4°F to 122°F)
Luftfuktighet 20 %~80 % RH
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Maximal dataöverföringshastighet 5 Gbps
Typ och hastighet USB 3.0 - 5 Gbit/s
SATA II (3 Gbps)
Port Multiplier Ja
Duplication Modes Sector by Sector (Whole Drive)
Duplication Speed 7GBpm
Raderingslägen Quick Erase
Maximal enhetskapacitet För närvarande testad med upp till 6 TB 7200 RPM
Raderingslägen 1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear)
3-Pass Overwrite
7-Pass Overwrite
Allmänna specifikationer Duplikationshastighet på 7 GB per minut
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 2 A
Utspänning 19V DC
Utström 5 A
Polaritet på mittpol Positiv
Kontakttyp M
Strömförbrukning 95
Utseende Kabinettyp Stål
Produktlängd 31,5 cm [12,4 in]
Produktbredd 15,2 cm [6,0 in]
Produkthöjd 75,0 mm [3,0 in]
Produktvikt 1,5 kg [3,3 lb]
Vad det är i lådan 1 - Ingår i paketet USB 3.0\eSATA 1:5 SATA HDD-dockningsstation med duplikator
USB 3.0-kabel
eSATA-kabel
4 - Ingår i paketet Gummifötter (installerade)
1 - Ingår i paketet universell strömadapter (NA, UK, EU, ANZ)
Instruktionsbok

Tillbehör

SAT2IDEADP

SATA till 2,5" eller 3,5" IDE-hårddisk-adapter för HDD-dockningsstationer

Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
HDDSLEV25

2.5in Silicone Laptop Hard Drive Protector Sleeve with Connector Cap

Provide protection against shocks/impacts to a 2.5in hard drive

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
HDDSLEV35

3,5" skyddshylsa i silikon med kontaktlock för hårddiskar

Skydda en 3,5" hårddisk mot elstötar/sammanstötningar

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25YW

2.5in Anti-Static Hard Drive Protector Case - Yellow (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25WH

2.5in Anti-Static Hard Drive Protector Case - White (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25OR

2.5in Anti-Static Hard Drive Protector Case - Orange (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25GN

2.5in Anti-Static Hard Drive Protector Case - Green (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25BL

2.5in Anti-Static Hard Drive Protector Case - Blue (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
HDDCASE25BK

2,5" antistatiskt skyddsfodral för hårddiskar - Svart (3-pack)

Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet

Ditt pris
€19,99 EUR excl. VAT
€24,99 EUR incl. VAT
USB3SAB3BK

3 ft Black SuperSpeed USB 3.0 Cable A to B - M/M

Connect to your external solutions and transfer data at 10x the speed of USB 2.0

Ditt pris
€6,99 EUR excl. VAT
€8,74 EUR incl. VAT
ESATA3

3 ft Shielded External eSATA Cable M/M

Connect your external SATA storage devices to your Laptop or desktop.

Ditt pris
€9,99 EUR excl. VAT
€12,49 EUR incl. VAT
ESATA6

1,8 m skärmad extern eSATA-kabel M/M

Anslut dina externa SATA-lagringsenheter till din bärbara eller stationära dator.

Ditt pris
€12,99 EUR excl. VAT
€16,24 EUR incl. VAT
ECESATA254F

2 Port Flush Mount ExpressCard 54mm eSATA II Controller Adapter Card

Add 2 flush mounted eSATA ports to a laptop through an ExpressCard/54 slot

Ditt pris
€32,99 EUR excl. VAT
€41,24 EUR incl. VAT
Utgått
ECUSB3S1

1 Port Flush Mount ExpressCard SuperSpeed USB 3.0 Card Adapter with UASP Support

Flush mount a USB 3.0 ExpressCard adapter into a laptop ExpressCard slot

Ditt pris
€22,46 EUR excl. VAT
€28,08 EUR incl. VAT
Utgått
ECESATA1

1 Port Flush Mount ExpressCard 34mm eSATA II Controller Adapter Card

Add a slim flush mounting eSATA port to a laptop through ExpressCard

Ditt pris
€27,99 EUR excl. VAT
€34,99 EUR incl. VAT
Utgått
PEXUSB3S2

PCI Express SuperSpeed USB 3.0-kortadapter med 2 portar och UASP-stöd

Lägg till två USB 3.0-portar till din stationära dator genom en PCI Express-utbyggnadskortplats

Ditt pris
€34,99 EUR excl. VAT
€43,74 EUR incl. VAT
Utgått
ECUSB3S2

2 Port ExpressCard SuperSpeed USB 3.0 Card Adapter with UASP Support

Add two USB 3.0 ports to your laptop through an ExpressCard slot

Ditt pris
€21,99 EUR excl. VAT
€27,49 EUR incl. VAT
Utgått
PEXESATA1

1 Port PCI Express eSATA II Controller Card

Add an eSATA port to a desktop computer through a PCI Express slot

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
USB3S2ESATA

91 cm SuperSpeed USB 3.0 till eSATA-kabeladapter

Få snabb tillgång till en eSATA-enhet från en USB 3.0-port

Ditt pris
€38,99 EUR excl. VAT
€48,74 EUR incl. VAT
SAT32M225

M.2 SATA SSD till 2,5-tums SATA-adapter - M.2 NGFF till SATA-konverterare - 7 mm - Fäste för öppen ram - M2-hårddiskadapter

M.2 SATA NGFF till 2,5-tums SATA | 7 mm hög | SATA 6 Gbit/s | Öppen ram

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
SAT32MSAT257

mSATA-SSD till 2,5" SATA-adapter-konverterare

Konvertera en mSATA-SSD till en 7 mm hög 2,5" SATA-SSD på 6 Gbps med öppen ram

Ditt pris
€33,99 EUR excl. VAT
€42,49 EUR incl. VAT
25SATSAS35

2,5" SATA/SAS SSD/HDD till 3,5" SATA-hårddisk-konverterare

Omvandlar i stort sett alla 2,5 tums SATA- och SAS-hårddiskar till en 3,5 tums SATA-hårddisk

Ditt pris
€22,99 EUR excl. VAT
€28,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time. 

 

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.

Before You Buy

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.

Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen