Fristående 2,5/3,5" SATA-hårddiskduplikator med backup-bibliotek för flera HDD/SSD-avbildningar

Duplicera en 2,5/3,5" hårddisk till en annan utan att ansluta till en dator, eller säkerhetskopiera flera hårddiskavbildningar till en biblioteksenhet för att enkelt återställa PC/server-avbildningar

Produkt ID: SATDUP11IMG

  • Backup-enhet med flera avbildningar för problemfri duplikation
  • Tre lägen för hårddisk-duplikation inklusive sektor-för-sektor med 6 GB/min
  • Stöd för hårddiskar (HDD) eller solid state-enheter (SDD) med 2,5 eller 3,5 tums formfaktor
Ditt pris
€521,99 EUR excl. VAT
€652,49 EUR incl. VAT

Den SATDUP11IMG fristående SATA-hårddiskduplikatorn låter dig skapa en exakt kopia av en SATA-hårddisk (HDD) / solid state-enhet (SSD) eller skapa en backup-enhet med flera avbildningar som du kan kopiera till flera enheter när som helst.

Snabb, enkel duplikation

Få mindre trassel med SATDUP11IMG som eliminerar antalet enheter som behövs vid säkerhetskopiering av flera unika hårddiskavbildningar. Med en enda backup-enhet kan du lagra flera unika hårddiskavbildningar på en enda SSD/HDD för att garantera snabb duplicering med 6 GB/min och minimalt med trassel. Detta är en idealisk lösning om du ofta gör avbildningar av olika datorsystem eftersom det innebär att du bara behöver ta med dig en backup-enhet för att återställa flera avbildningar på olika system.

Problemfri prestanda

Den mångsidiga duplikatorn har även tre olika lägen för ett-till-ett-duplicering: fil- & systemkopiering, kopiering av alla partitioner och hel kopiering. Detta är idealiskt för engångsduplikation eftersom man slipper skapa en hårddiskavbildning för ett engångsprojekt.

Intuitiv användning

SATDUP11IMG garanterar problemfri installation och kontroll med en lättläst LCD-skärm och intuitiv meny med fyra knappar. Menyn ger dig tillgång till många värdefulla funktioner som garanterar enkla hanteringar som till exempel: enhet till enhet-duplikation, enhet till backup-bibliotek och återställning och mycket mer. Den ger dessutom många avancerade alternativ för erfarna användare.

SATDUP11IMG stöder användning av olika enhetsadaptrar för extra kompatibilitet med olika enhetstyper vid duplicering. Listan nedan över StarTech.com-adaptrar har testats specifikt för att garantera kompatibilitet med denna enhetsduplikator:

2,5/3,5in IDE-enheter - SAT2IDEADP
mSATA-enheter - SAT2MSAT25
M.2-enheter (NGFF) - SAT32M225

SATDUP11IMG är TAA-kompatibel och täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Kriminaltekniker som behöver ha speglingar/kloningar för att skapa en exakt kopia av källdisken på en annan hårddisk.
  • Yrkesverksamma som behöver identiska säkerhetskopior när det är av yttersta vikt att datan är komplett, som till exempel vid dataåterställning
  • Klona hårddiskar som innehåller dolda partitioner som vissa program för hårddisk-kloning hoppar över
  • Systembyggare/IT-specialister som behöver flera olika hårddiskavbildningar för olika systembyggen

Fördelarna med StarTech.com

  • Problemfri enhetsduplikation med flera unika hårddiskavbildningar på samma HDD/SSD
  • Spara tid genom att snabbt duplicera hårddiskar med hastigheter på upp till 6 GB per minut

Partnernummer

  • Ingram Micro Sweden V933251
  • UPC 065030858076

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 11,9 cm [4,7 in]
Package Length 26,7 cm [10,5 in]
Package Width 18,5 cm [7,3 in]
Fraktvikt (förpackning) 1,7 kg [3,8 lb]
Hårdvara Gränssnitt SATA
Antal enheter 2
Enhetsstorlek 2.5in & 3.5in
Enhetstyp SATA
Indikatorer 1 - LED-indikatorer Strömindikator för källenhet
Aktivitetsindikator för källenhet
Felindikator för källenhet
Strömindikator för målenhet
Aktivitetsindikator för målenhet
Felindikator för målenhet
LCD-skärm
Kontakt(er) 2 - Enhetskontakter SATA data- & ström-kombo (7+15-stifts)
Miljö Drifttemperatur 5°C to 45°C (41°F to 113°F)
Förvaringstemperatur -20°C to -85°C (-4°F to 185°F)
Luftfuktighet 20% ~ 80%
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Typ och hastighet SATA III (6 Gbps)
Duplication Modes System and File
Duplication Speed 6GBpm
Maximal enhetskapacitet För närvarande testad med upp till 6 TB 7200 RPM 3,5"-hårddiskar per fack och 1 TB 7200 RPM 2,5"-hårddiskar per fack
Duplication Modes All Partitions
Sector by Sector (Whole Drive)
Percentage Copy
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 1.4A
Utspänning 12V DC
Utström 5A
Polaritet på mittpol Positiv
Strömförbrukning 60
Särskilda anmärkningar/krav Obs. Vid duplicering måste målhårddisken vara lika stor som eller större än källhårddisken.
Utseende Kabinettyp Stål
Produktlängd 12,9 cm [5,1 in]
Produktbredd 77 mm [3,0 in]
Produkthöjd 28 mm [1,1 in]
Produktvikt 350 g [12,4 oz]
Vad det är i lådan 1 - Ingår i paketet 1:1 HDD/SSD-duplikator
Lång SATA-kabel
2 - Ingår i paketet Kort SATA-kabel
1 - Ingår i paketet eSATA + 12 V strömkabel (strömkontakt typ M)
eSATA + 5 V strömkabel (strömkontakt typ F)
2 - Ingår i paketet HDD/SSD-dynor
1 - Ingår i paketet Universell strömadapter (UK/NA/EU)
Instruktionsbok

Tillbehör

Utgått
HDDCASE25WH

2.5in Anti-Static Hard Drive Protector Case - White (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25BL

2.5in Anti-Static Hard Drive Protector Case - Blue (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
HDDSLEV25

2.5in Silicone Laptop Hard Drive Protector Sleeve with Connector Cap

Provide protection against shocks/impacts to a 2.5in hard drive

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
Utgått
SAT2CF

SATA to Compact Flash SSD Adapter

Turn a Compact Flash card into a bootable SATA SSD

Ditt pris
€40,99 EUR excl. VAT
€51,24 EUR incl. VAT
SAT2MSAT25

2,5" SATA till mini SATA-SSD-adapterhölje

Konvertera en mSATA mini-SSD till en vanlig 2,5" SATA-SSD

Ditt pris
€38,99 EUR excl. VAT
€48,74 EUR incl. VAT
25SATSAS35

2,5" SATA/SAS SSD/HDD till 3,5" SATA-hårddisk-konverterare

Omvandlar i stort sett alla 2,5 tums SATA- och SAS-hårddiskar till en 3,5 tums SATA-hårddisk

Ditt pris
€22,99 EUR excl. VAT
€28,74 EUR incl. VAT
Utgått
HDDCASE25OR

2.5in Anti-Static Hard Drive Protector Case - Orange (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
HDDCASE25BK

2,5" antistatiskt skyddsfodral för hårddiskar - Svart (3-pack)

Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet

Ditt pris
€19,99 EUR excl. VAT
€24,99 EUR incl. VAT
Utgått
HDDCASE25GN

2.5in Anti-Static Hard Drive Protector Case - Green (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25YW

2.5in Anti-Static Hard Drive Protector Case - Yellow (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
HDDSLEV35

3,5" skyddshylsa i silikon med kontaktlock för hårddiskar

Skydda en 3,5" hårddisk mot elstötar/sammanstötningar

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
SAT2IDEADP

SATA till 2,5" eller 3,5" IDE-hårddisk-adapter för HDD-dockningsstationer

Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
SDOCKU33EBV

eSATA/USB 3.0-dockningsstation med UASP för SATA III-SSD/HDD

Docka dina 2,5" eller 3,5" SATA 6 Gbps SSD/HDD-enheter över eSATA eller USB 3.0 med UASP

Ditt pris
€76,99 EUR excl. VAT
€96,24 EUR incl. VAT
SVA12M5NA

DC-strömadapter - 12 V, 5 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€65,99 EUR excl. VAT
€82,49 EUR incl. VAT
S251SMU33EP

Externt eSATAp/eSATA- eller USB 3.0-kabinett med UASP för 2,5" SATA III 6 Gbps-hårddiskar – Bärbar HDD/SDD

Gör om en 2,5" SATA III HDD/SSD till en extern hårddisk som kan ansluta till datorn genom antingen eSATAp med 6 Gbps eller USB 3.0 med UASP med 5 Gbps

Ditt pris
€58,99 EUR excl. VAT
€73,74 EUR incl. VAT
Utgått
SAT2510U2E

2,5" eSATA USB kabinett för extern SATA-hårddisk

Gör om en 2,5" SATA-hårddisk till en USB 2.0- eller extern eSATA-hårddisk

Ditt pris
€27,99 EUR excl. VAT
€34,99 EUR incl. VAT
Utgått
SAT2510BU2E

2,5" svart eSATA USB kabinett för extern SATA-hårddisk

Gör om en 2,5" SATA-hårddisk till en USB 2.0- eller extern eSATA-hårddisk

Ditt pris
€26,99 EUR excl. VAT
€33,74 EUR incl. VAT
Utgått
S3510BMU33ET

USB 3.0 eSATA Hard Drive Enclosure - Trayless 3.5" SATA III HDD Enclosure - SATA 6 Gbps - Black

Easily connect and hot swap 3.5in SATA III hard drives, through either eSATA or UASP-supported USB 3.0

Ditt pris
€70,99 EUR excl. VAT
€88,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Inbyggd programvara

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.

Before You Buy

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.

Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

Quick and secure erase functions

Quick erase and secure erase are functions the duplicators call on the hard drives themselves. How they work depends on the manufacturer of the hard drive.

Department of Defense erase function

A Department of Defense (DoD) erase is a function performed by the duplicator where it does three passes. The first pass writes all 0s. The second pass writes all 1s. The third pass writes 0s and 1s randomly.

Note: Not all duplicators will feature all of these erase modes. It is important to review the product manual to confirm the available erase modes.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen
Vänta...