Mini SAS SFF-8087 to 4x 2.5in SATA/SAS 5.25in Hot Swap Backplane

Add 4 Removable SATA/SAS Hard Drives through a Single 5.25in Bay

Produkt ID: SATSAS425BK

  • Hold up to four 2.5in SATA/SAS drives
  • Entire unit fits into a single 5.25in front panel bay
  • Supports 2.5" form factor hard drives (HDD) and solid state drives (SSD) up to 15mm in height

The SATSAS425BK 4-Drive 2.5in SATA/SAS Hot-swap Backplane lets you install four 2.5" SATA and/or SAS hard drives into a single 5.25in front bay. Using a single Mini SAS SFF-8087 interface for quick setup and easy maintenance and with removable trays, each drive can be replaced or swapped out without having to open up the computer chassis.

To maximize performance and utilize the full speed potential of your SATA III hard drives, this HDD Backplane supports SATA III for transfer speeds up to 6 Gbps when paired with a compatible controller.

Each removable tray features a locking mechanism that prevents unauthorized removal of the drives, and also power and activity LEDs. Constructed from lightweight and durable aluminum to help with heat dissipation, the backplane also features a 40mm cooling fan to help increase air flow.


  • Add up to 4 SATA/SAS hard drives to small form factor systems with a limited number of hard drive bays
  • Add convenient removable storage for backups or RAID storage systems
  • Maximize hard drive density in a system by adding 4 hard drives for each 5.25in bay
  • Build a small, power-efficient storage array with low-powered 2.5in drives

Fördelarna med StarTech.com

  • Maximize performance, with file transfer speeds up to 6Gbps when paired with SATA III HDD and controller
  • Install four easily removable/swappable hard drives into a single 5.25in bay
  • Removable hard drive trays with locks, for quick, convenient and secure access to SATA/SAS hard drives
  • Supports up to 15mm height 2.5in hard drives, including high-capacity SATA drives and SAS drives


  • UPC 065030844871



Warranty Information Warranty 2 Years
Förpackning Förpackningsantal 1
Package Length 21,8 cm [8,6 in]
Package Width 17,2 cm [6,8 in]
Package Height 52 mm [2,0 in]
Fraktvikt (förpackning) 707 g [25,0 oz]
Hårdvara Nyckellås Ja
Rättsliga godkännanden UL94 V-0 Rated
Antal enheter 4
Enhetsstorlek 2.5in
Enhetstyp SAS & SATA
Enhetsinstallation Fixerad
Antal 2,5 tums fack 4
Fläkt(ar) Ja
1 - Flaktar 40 mm
Indikatorer 4 - LED-indikatorer HDD Power/Activity
Kontakt(er) 4 - Enhetskontakter SFF-8482 (29-stifts, data & ström, intern SAS)
1 - Värdkontakter LP4 (4-stift, Molex-type Large Drive Power)
SFF-8087 (36-stifts, intern Mini-SAS)
Miljö Drifttemperatur 5°C to 80°C (41°F to 176°F)
Förvaringstemperatur -40°C to 70°C (-40°F to 158°F)
Luftfuktighet 8% ~ 90% RH
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda RAID Nej
Hot swap-förmåga Ja
Inlänkningshastighet 3, 000 cycles
Temperaturlarm Nej
Särskilda anmärkningar/krav System- och kabelkrav Available 5.25in front expansion bay
SFF-8087 Mini SAS Cable
Obs. SATA drives can be used on both SATA or SAS controllers, but SAS drives can only be used on SAS controllers
Utseende Färg Svart
Kabinettyp Aluminium och plast
Maximal enhetshöjd 15 mm [0,6 in]
Produktlängd 15,6 cm [6,1 in]
Produktbredd 14,5 cm [5,7 in]
Produkthöjd 4,2 cm [1,7 in]
Produktvikt 577 g [20,4 oz]
Vad det är i lådan 1 - Ingår i paketet 5.25in SATA/SAS Backplane
6in LP4 Molex to SATA Power Cable
Set of keys
Package of mounting screws
Instruction Manual



100 cm Serial Attached SCSI SAS-kabel - SFF-8087 till SFF-8087

Ger pålitlig anslutning till högpresterande nätverk, servrar, arbetsstationer och stationära datorer

Ditt pris
€54,99 EUR excl. VAT
€68,74 EUR incl. VAT

50 cm SFF-8087 till 4x SATA - intern Mini SAS till SATA omvänd kabel

Anslut mini SAS-bakplan till en SAS-/SATA RAID-kontroller eller -moderkort

Ditt pris
€47,99 EUR excl. VAT
€59,99 EUR incl. VAT


Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)




Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor


When you troubleshoot issues with a hard drive rack, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • SATA and SAS cables
  • Hard drives
  • Hard drive rack

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive rack in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive rack in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive rack, it is recommended that you do the following:

  • To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter.  Check to see if your hard drive is listed.
  • If the hard drive is listed with unallocated space, it needs to be formatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.

  • If the hard drive is listed as healthy but does not have a drive letter assigned to it, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

Before You Buy

Although mobile racks can enable a Serial Attached SCSI (SAS) drive to connect using a standard Serial ATA (SATA) connector, the hard drive controller must be SAS compatible to properly support SAS drives. SAS controllers can work with SAS and SATA drives, but most SAS drives will only work with a SAS controller.

For further information about SAS and SATA interoperability, refer to the following FAQ: http://www.startech.com/faq/hard_drive_controllers_sas_drive_compatibility.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen