USB 3.1 (10 Gbps) fristående dupliceringsdockningsstation för 2,5" & 3,5" SATA SSD/HDD-enheter - med snabb duplicering på upp till 28 GB/min

Duplicera eller docka en SATA SSD/HDD-enhet med snabb prestanda - fungerar med både USB-C- och USB-A-kapabla enheter

Produkt ID: SDOCK2U313R

  • Duplicera hårddiskar snabbt utan en värddator, med hastigheter på upp till 28 GB per minut för SSD-enheter
  • Fungerar med både USB-C- och USB-A-kapabla enheter med två medföljande kablar
  • Kompatibel med Thunderbolt 3 USB-C-port
Ditt pris
€187,99 EUR excl. VAT
€234,99 EUR incl. VAT

Duplicera enheter snabbt med hastigheter på upp till 28 GB per minut för SSD-enheter utan att behöva ansluta till datorn. Dupliceringsdockningsstationen har fristående enhetskloning som gör det enkelt att säkerhetskopiera din data och göra exakta avbildningar av dina enheter. Du kan dessutom ansluta dockningsstationen till din dator genom USB 3.1 (10 Gbps) för att docka och byta dina enheter som en del av en skalbar lagringslösning.  

Klona dina enheter med hög hastighet

Duplicera dina hårddiskar snabbt utan att ens ansluta till en värddator

Att duplicera en hårddisk eller solid state-enhet är ett effektivt sätt att flytta ditt operativsystem och din data från en enhet till en annan, eller för att skapa en exakt kopia för att skydda din viktiga data. Denna enhetsduplikator låter dig skapa en klon av din enhet, sektor-för-sektor, inklusive partitioner och information om startsektor för att garantera dataintegritet och konsekvens för känsliga operationer som dataåterställning.

Dupliceringsdockningsstationen besparar dig värdefull tid med SSD-dupliceringshastigheter på upp till 28 GB per minut. Du kan enkelt duplicera en 2,5" eller 3,5" SATA SSD- eller HDD-enhet utan att behöva ansluta duplikatorn till en värddator. 

För över filer snabbt mellan dockningsstationen och din PC

Docka dina HDD- och SSD-enheter och få snabb åtkomst till dina filer med dataöverföringshastigheter på upp till 10 Gbps

Dupliceringsdockningsstationen är dessutom en extern lagringslösning som låter dig docka dina enheter genom USB 3.1 Gen 2 med UASP-stöd för höga dataöverföringshastigheter på upp till 10 Gbps. Varje enhetsport har individuellt stöd för en hårddisk med hög kapacitet eller solid state-enhet, testad upp till 6 TB.

Två USB-kablar medföljer för mångsidighet

Dupliceringsdockningsstationen levereras med två USB-kablar för flexibel användning med de senaste bärbara datorerna och surfplattorna med en USB-C™-port, samt äldre enheter. Både USB-C till B- och USB-A till B-kablar ingår. Dupliceringsdockningsstationen är dessutom kompatibel med en Thunderbolt™ 3 USB-C-port.

Designad för enkel användning

Dockningsstationen har toppmatning i brödrost-stil som gör det enkelt att föra in enheterna. Den har dessutom enhetsdörrar som hjälper till att stabilisera enheterna som är införda i porten och förhindrar främmande objekt att komma in.

Dupliceringsdockningsstationen är både verktygslös och hyllfri för snabba och problemfria insättningar. LED-indikatorer låter dig veta på håll dupliceringsprocessens nuvarande status, inklusive det specifika dupliceringsläget, HDD-status och kloningsprogressen. HDD-utmatningsknappen gör det snabbt och enkelt att ta ur en enhet.

SDOCK2U33RE stöder användning av olika enhetsadaptrar för extra kompatibilitet med olika enhetstyper vid duplicering och dockning. Listan nedan över StarTech.com-adaptrar har testats specifikt för att garantera kompatibilitet med denna enhetsduplikator:

SAT2IDEADP - SAT2IDEADP
SAT2MSAT25 - SAT2MSAT25
SAT32M225 - SAT32M225

SDOCK2U313R täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Duplicera en 2,5" eller 3,5" SSD/HDD för att skapa en exakt kopia av källdiskten på en annan hårddisk
  • Skapa identiska säkerhetskopior för systembyggen som kräver samma enhetsavbildning
  • Få åtkomst till eller byt hårddiskar och solid state-enheter snabbt för enkel säkerhetskopiering/återställning av data

Partnernummer

  • Ingram Micro Sweden V933690
  • ALSO Sweden 000000000002776115
  • UPC 065030863551

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 88 mm [3,5 in]
Package Length 16,6 cm [6,5 in]
Fraktvikt (förpackning) 992 g [35,0 oz]
Package Width 30 cm [11,8 in]
Hårdvara Gränssnitt USB 3.1 Gen 2
Busstyp USB 3.1 Gen 2
Antal enheter 2
Enhetsstorlek 2.5in & 3.5in
Enhetstyp SATA
Enhetsinstallation Löstagbar
Fläkt(ar) Nej
Chipset-ID ASMedia - ASM1352R
Indikatorer 1 - LED-indikatorer Ström
Läge
2 - LED-indikatorer HDD-status
1 - LED-indikatorer Klon
Kontakt(er) 2 - Enhetskontakter SATA data- & ström-kombo (7+15-stifts)
1 - Värdkontakter USB 3.1 USB Type-B (9-stifts, Gen 2, 10 Gbps)
Miljö Drifttemperatur 5°C - 35°C (41°C to 95°C)
Förvaringstemperatur -20°C - 50°C (-4°C to 122°C)
Luftfuktighet 20 ~ 80 % RH
Mjukvara OS-kompatibilitet Operativsystemsoberoende, varken programvara eller drivrutiner behövs
Prestanda Maximal dataöverföringshastighet 10 Gbps
Typ och hastighet USB 3.1 Gen 2 - 10 Gbit/s
UASP-stöd Ja
TRIM Support Ja
4Kn Support Ja
Typ och hastighet SATA III (6 Gbps)
Port Multiplier Nej
RAID Nej
Duplication Modes Sector by Sector (Whole Drive)
Duplication Speed 28GBpm
Maximal enhetskapacitet Testat med enheter med upp till 6 TB
Hot swap-förmåga Ja
Särskilda anmärkningar/krav Obs. Windows 7 and earlier Windows versions do not support TRIM with USB to SATA devices.
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 1.5A
Utspänning 12V DC
Utström 3000 mA
Polaritet på mittpol Positiv
Kontakttyp M
Strömförbrukning 36
Utseende Färg Svart
Kabinettyp Av plast
Maximal enhetshöjd 25,4 mm [1,0 in]
Produktlängd 14,2 cm [5,6 in]
Produktbredd 13,2 cm [5,2 in]
Produkthöjd 70 mm [2,8 in]
Produktvikt 508 g [17,9 oz]
Vad det är i lådan 1 - Ingår i paketet USB 3.1-dupliceringsdockningsstation
USB-C till B-kabel - 101 cm
USB 3.0 A- till B-kabel - 103 cm
universell strömadapter (NA/EU/UK/AU) - 103 cm (kabel)
Snabbstartsguide

Tillbehör

USB3SAB1MRA

1m Black SuperSpeed USB 3.0 Cable - Right Angle A to B - M/M

Connect USB 3.0 devices, even in hard to reach areas and tight spaces

Ditt pris
€10,99 EUR excl. VAT
€13,74 EUR incl. VAT
USB3CAB1M

1m (3ft) Certified SuperSpeed USB 3.0 A to B Cable - M/M

Connect your USB 3.0 devices with this high-quality USB 3.0 certified cable

Ditt pris
€13,99 EUR excl. VAT
€17,49 EUR incl. VAT
USB3SAB3BK

3 ft Black SuperSpeed USB 3.0 Cable A to B - M/M

Connect to your external solutions and transfer data at 10x the speed of USB 2.0

Ditt pris
€6,99 EUR excl. VAT
€8,74 EUR incl. VAT
USB31CB1M

USB 3.1 USB-C till USB-B-kabel - 1 m

Anslut USB 3.1 eller 3.0 USB-B-enheter till din USB-C-värd

Ditt pris
€25,99 EUR excl. VAT
€32,49 EUR incl. VAT
SAT2IDEADP

SATA till 2,5" eller 3,5" IDE-hårddisk-adapter för HDD-dockningsstationer

Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
HDDSLEV25

2.5in Silicone Laptop Hard Drive Protector Sleeve with Connector Cap

Provide protection against shocks/impacts to a 2.5in hard drive

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
Utgått
HDDCASE25WH

2.5in Anti-Static Hard Drive Protector Case - White (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25YW

2.5in Anti-Static Hard Drive Protector Case - Yellow (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
PEXUSB3S2

PCI Express SuperSpeed USB 3.0-kortadapter med 2 portar och UASP-stöd

Lägg till två USB 3.0-portar till din stationära dator genom en PCI Express-utbyggnadskortplats

Ditt pris
€34,99 EUR excl. VAT
€43,74 EUR incl. VAT
PEXUSB3S11

PCI Express SuperSpeed USB 3.0-kort med 2 portar och UASP-stöd - 1 Intern, 1 extern

Lägg till en intern och en extern SuperSpeed USB 3.0 till din dator

Ditt pris
€49,99 EUR excl. VAT
€62,49 EUR incl. VAT
HDDCASE25BK

2,5" antistatiskt skyddsfodral för hårddiskar - Svart (3-pack)

Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet

Ditt pris
€19,99 EUR excl. VAT
€24,99 EUR incl. VAT
HDDSLEV35

3,5" skyddshylsa i silikon med kontaktlock för hårddiskar

Skydda en 3,5" hårddisk mot elstötar/sammanstötningar

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25BL

2.5in Anti-Static Hard Drive Protector Case - Blue (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25GN

2.5in Anti-Static Hard Drive Protector Case - Green (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25OR

2.5in Anti-Static Hard Drive Protector Case - Orange (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
PEXUSB3S4V

PCI Express PCIe SuperSpeed USB 3.0-kontrollerkortadapter med 4 portar och UASP - SATA-ström

Lägg till 4 externa USB 3.0-portar till en dator i låg- eller standardprofil genom PCI express

Ditt pris
€63,99 EUR excl. VAT
€79,99 EUR incl. VAT
Utgått
PEXUSB3S400

PCI Express PCIe SuperSpeed USB 3.0-kontrollerkortadapter med 4 oberoende portar och UASP - SATA-ström

Lägg till 4 oberoende SuperSpeed USB 3.0-portar till datorn genom en PCI express-kortplats

Ditt pris
€138,99 EUR excl. VAT
€173,74 EUR incl. VAT
MPEXUSB3S22B

2 Port SuperSpeed Mini PCI Express USB 3.0 Adapter Card w/ Bracket Kit and UASP Support

Add two USB 3.0 ports through a Mini PCI Express slot

Ditt pris
€77,99 EUR excl. VAT
€97,49 EUR incl. VAT
Utgått
PEXUSB3S22

SuperSpeed USB 3.0 PCI Express-kort med 2 portar och UASP - SATA-ström

Lägg till 2 USB 2.0-portar till din stationära dator genom en PCI Express-kortplats

Ditt pris
€39,99 EUR excl. VAT
€49,99 EUR incl. VAT
Utgått
MPEXUSB3S2

2 Port Mini PCI Express SuperSpeed USB 3.0 Card Adapter with UASP Support

Add 2 USB 3.0 ports through a mini PCI Express slot

Ditt pris
€46,46 EUR excl. VAT
€58,08 EUR incl. VAT
Utgått
PEXUSB3S4

SuperSpeed USB 3.0 PCI Express-kort med 4 portar och UASP - SATA-ström

Lägg till fyra USB 3.0-portar till din stationära dator genom en PCI Express-utbyggnadskortplats

Ditt pris
€50,99 EUR excl. VAT
€63,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Inbyggd programvara

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time. 

 

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.

If your setup components support USB 3.1 but you are experiencing slower transfer speeds than you expected, consider the following:

  • A USB host connection with multiple USB 3.1 ports might not be able to support 10Gbps on each port simultaneously.
  • The type of port on a device does not determine whether the device is capable of USB 3.1 speeds. A USB-C port might not support USB 3.1 speeds, while USB-A and USB-B ports might support USB 3.1 speeds.
  • Any other devices that you include in your setup, such as an older hard drive in a USB 3.1 enclosure, might create a point of congestion and slow down transfer speeds.

To confirm the functionality of your USB host connection, its ports, and any other devices in your setup, refer to the information provided by the manufacturer.

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

Du bör inte uppgradera enhetens inbyggda programvara om du inte har några problem med enhetens funktioner. Du behöver bara uppgradera om du har problem med enheten och är säker på att problemet är den inbyggda programvaran.  Du kan bekräfta detta genom att läsa igenom den medföljande dokumentationen eller kontakta vår tekniska avdelning. Felaktig uppgradering av inbyggd programvara kan resultera i minskade prestanda så vi rekommenderar att du kontaktar StarTech.com först.

Hur man

To confirm that Windows detects your USB device, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Before You Buy

Yes, this device supports the TRIM command. If the OS issues a TRIM command, the command will be passed to the connected device.

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.

Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

USB 3.1 is the most recent version of the USB (Universal Serial Bus) standard for connecting computers and electronic devices. It is capable of data transfer speeds up to 10Gbps, and while it can use the USB-C connector type, it can also use a variety of other connector types. To achieve USB 3.1 transfer speeds, your USB host connection, cables, and device must all support USB 3.1. USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). 

USB 3.0 is capable of data transfer speeds up to 5Gbps. USB 3.0 is also known as USB 3.1 Gen 1 (5Gbps).

USB 3.1 is backwards compatible with USB 3.0 and USB 2.0, except in the following scenarios:

  • USB-B 3.1 cables are not compatible with USB-B 2.0 ports.
  • Unless you use an adapter, USB-C ports or cables will not work with USB-A or USB-B ports or cables.
  • Devices that require USB 3.1 transfer speeds of 10Gbps might not work with USB 3.0 or USB 2.0, or you might experience lower transfer speeds and impacted performance.
  • Bus-powered USB devices that requires more power than what USB 2.0 can provide are not compatible with USB 2.0.

To transfer data at speeds of 10Gbps, you need to confirm that the following components in your setup support USB 3.1:

  • The USB host connection
  • The USB cable
  • The USB device and any subcomponents (for example, a hard drive docking station and the hard drives in the docking station)

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

The included USB cable for this USB 3.1 Gen 2 device has been tested and verified to perform at USB 3.1 Gen 2 speeds of 10Gbps.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen
Vänta...