Produkt ID: SDOCKU313E
Anslut och nå vilken 2,5" eller 3,5" SATA-hårddisk eller SSD som helst med hjälp av denna dockningsstation för en enda hårddisk, över en USB 3.1 Gen 2- (upp till 10 Gbps) eller eSATA-anslutning.
Dockningsstationen är idealisk för IT-proffs och ger dig snabb åtkomst till en SATA solid state-enhet eller hårddisk för imaging, dataåterställning och säkerhetskopiering.
Du kan ansluta antingen genom USB 3.1 Gen 2 eller eSATA och utnyttja den höga prestandan från de senaste SSD- och HDD-enheterna.
Dockningsstationens vertikala hårddiskorientering gör det enkelt att docka och byta hårddiskar från din stationära eller bärbara dator. Du för helt enkelt in din SSD eller HDD i hårddiskspringan ovanpå dockningsstationen utan att några verktyg eller brickor behövs. HDD-utmatningsknappen ger snabb och enkel frånkoppling av enhet.
Dockningsstationen med ett fack har en USB Type-A till Type-C-kabel för att ansluta till nyare USB-C-kapabla enheter. Den har även en USB Type-A till Type-B-kabel som ger bakåtkompatibilitet med dina befintliga USB 3.0-, 2.0- och 1.x-enheter. Även en eSATA-kabel medföljer.
Dockningsstationen är även UASP-kompatibel, för förbättrad prestanda.
SDOCKU313E täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Package Height | 91 mm [3,6 in] |
Package Length | 17,1 cm [6,7 in] | |
Fraktvikt (förpackning) | 862 g [30,4 oz] | |
Package Width | 16,1 cm [6,3 in] | |
Hårdvara | Gränssnitt | USB 3.1 Gen 2 |
Busstyp | USB 3.1 Gen 2 & eSATA | |
Gränssnitt | eSATA | |
Antal enheter | 1 | |
Enhetsstorlek | 2.5in & 3.5in | |
Enhetstyp | SATA | |
Enhetsinstallation | Löstagbar | |
Fläkt(ar) | Nej | |
Chipset-ID | ASMedia - ASM1351 | |
Indikatorer | 1 - LED-indikatorer | Ström & aktivitet |
Kontakt(er) | 1 - Enhetskontakter | SATA data- & ström-kombo (7+15-stifts) |
1 - Värdkontakter | USB 3.1 USB Type-B (9-stifts, Gen 2, 10 Gbps) | |
eSATA (7-stifts, data) | ||
Miljö | Drifttemperatur | 5°C to 35°C (41°F to 95°F) |
Förvaringstemperatur | -20°C to 50°C (-4°F to 122°F) | |
Luftfuktighet | 20% ~ 80% RH | |
Mjukvara | OS-kompatibilitet | OS independent; No software or drivers required |
Prestanda | Typ och hastighet | USB 3.1 Gen 2 - 10 Gbit/s |
UASP-stöd | Ja | |
4Kn Support | Ja | |
Typ och hastighet | SATA III (6 Gbps) | |
TRIM Support | Ja | |
Maximal enhetskapacitet | För närvarande testad med hårddiskar på upp till 6TB vid 7200 RPM | |
Hot swap-förmåga | Ja | |
Särskilda anmärkningar/krav | Obs. | Windows 7 and earlier Windows versions do not support TRIM with USB to SATA devices. |
Ström | Power Source | AC-adapter medföljer |
Inspänning | 100 - 240 AC | |
Inström | 0.6 A | |
Utspänning | 12V DC | |
Utström | 2.0 A | |
Polaritet på mittpol | Positiv | |
Kontakttyp | M | |
Strömförbrukning | 24 | |
Utseende | Färg | Svart |
Kabinettyp | Av plast | |
Produktlängd | 14,5 cm [5,7 in] | |
Produktbredd | 93 mm [3,7 in] | |
Produkthöjd | 63,4 mm [2,5 in] | |
Produktvikt | 410 g [14,5 oz] | |
Vad det är i lådan | 1 - Ingår i paketet | USB 3.1 & eSATA HDD/SSD-dockningsstation |
universell strömadapter (NA/JP, EU, UK, ANZ) | ||
1 m USB-A till USB-B-kabel | ||
1 m USB-C till USB-B-kabel | ||
1 m eSATA-kabel | ||
snabbstartsguide |
Connect your USB 3.0 devices with this high-quality USB 3.0 certified cable
Connect to your external solutions and transfer data at 10x the speed of USB 2.0
Skydda en 3,5" hårddisk mot elstötar/sammanstötningar
Provide protection against shocks/impacts to a 2.5in hard drive
Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet
Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation
Konvertera en mSATA-SSD till en 7 mm hög 2,5" SATA-SSD på 6 Gbps med öppen ram
Konvertera en M.2 SSD till en 7 mm hög 2,5" SATA-SSD 6 Gbps med öppen ram
Gör om en standard SATA-moderkortsanslutning till en extern eSATA-port
Add an eSATA port to your PC, extended from internal Serial ATA connection port
Turn two standard SATA motherboard connections into two external eSATA ports
Anslut dina externa SATA-lagringsenheter till din bärbara eller stationära dator.
Lägg till två eSATA-portar till din dator, en förlängning från interna seriella ATA-anslutningsportar
1ft Latching SATA to Low Profile eSATA Plate Adapter
Gör om en standard SATA-moderkortsanslutning till en extern eSATA-port
Connect your external SATA storage devices to your Laptop or desktop.
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:
Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time.
Du bör inte uppgradera enhetens inbyggda programvara om du inte har några problem med enhetens funktioner. Du behöver bara uppgradera om du har problem med enheten och är säker på att problemet är den inbyggda programvaran. Du kan bekräfta detta genom att läsa igenom den medföljande dokumentationen eller kontakta vår tekniska avdelning. Felaktig uppgradering av inbyggd programvara kan resultera i minskade prestanda så vi rekommenderar att du kontaktar StarTech.com först.
Yes, this device supports the TRIM command. If the OS issues a TRIM command, the command will be passed to the connected device.
To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.