M.2 SSD-kabinett för M.2 SATA SSD-enheter - USB 3.1 (10 Gbit/s) med USB-C-kabel

Gör om din M.2 SATA-hårddisk till en supersnabb, superbärbar lagringslösning för USB-C-kapabla enheter

Produkt ID: SM21BMU31C3

  • Utnyttja din SATA M.2 SSD för att lägga till snabb extern lagring till din USB-C-kapabla värd (USB-C-kabel medföljer)
  • Stöder USB 3.1 Gen 2 (10 Gbps)
  • Kompatibel med Thunderbolt 3 USB-C-port
Ditt pris
€48,99 EUR excl. VAT
€61,24 EUR incl. VAT

Med detta kompakta M.2 SATA SSD-kabinett kan du lägga till väldigt bärbar datalagring till en dator med en USB-C™-port - som till exempel MacBook, Chromebook Pixel™, Dell™ XPS och många andra bärbara datorer. Det gör om din SATA M.2-hårddisk till en lagringslösning med hög hastighet över en USB 3.1 Gen 2-anslutning med genomströmning på upp till 10 Gbps.

En verkligt bärbar lösning

Detta slimmade kabinett i fickstorlek för M.2 NGFF SATA SSD-enheter har särskilt designats för mobilitet med en liten formfaktor som enkelt får plats i datorväskan. Dess lätta men ändå hållbara aluminiumhölje hjälper till att garantera att hårddisken inte skadas när du är ute och reser.

Ventilationshål hjälper till avleda värme för en optimal driftstemperatur.

Ventilationshålen hjälper till avleda värme för en optimal driftstemperatur

Maximera prestandan på din M.2 SATA SSD

Utnyttja hastigheten på din M.2 NGFF SATA-hårddisk med detta externa kabinett. Det ger USB 3.1 Gen 2-dataöverföringshastigheter på upp till 10 Gbps samt UASP-stöd så att du kan uppnå högre överföringshastigheter när du ansluter det till en UASP-kapabel värddator.

Kabinettet fungerar med surfplattor, bärbara datorer och stationära datorer och är kompatibel med värdar utrustade med Thunderbolt 3 USB-C-portar.

Bred kompatibilitet

Kabinettet är kompatibelt med alla vanliga M.2 SATA SSD-enheter och låter dig montera flera hårddisklängder, inklusive: 30 mm (2230), 42 mm (2242), 60 mm (2260) och 80 mm (2280).

SM21BMU31C3 täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Mobila proffs kan använda sin M.2 SATA SSD för få dataåtkomst med hög hastighet för sin USB-C-kapabla bärbara eller stationära dator
  • Återanvänd en M.2 SATA SSD som en extern USB 3.1 Gen 2-enhet
  • För över filer snabbare genom att använda en högpresterande SATA M.2 SSD som din externa hårddisk

Partnernummer

  • ALSO Sweden 000000000002776167
  • UPC 065030864435

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 32 mm [1,3 in]
Package Length 13,1 cm [5,2 in]
Fraktvikt (förpackning) 139 g [4,9 oz]
Package Width 16,1 cm [6,3 in]
Hårdvara Gränssnitt USB 3.1 Gen 2
Busstyp USB 3.1 Gen 2
Antal enheter 1
Enhetstyp M.2 (SATA, B-Key, NGFF)
M.2 (SATA, B+M-Key, NGFF)
Enhetsinstallation Fixerad
Chipset-ID ASMedia - ASM1351
Indikatorer 1 - LED-indikatorer Ström & aktivitet
Kontakt(er) 1 - Enhetskontakter M.2 (SATA, B-Key, NGFF)
1 - Värdkontakter USB 3.1 USB type Micro-B (10-stifts, Gen 2, 10 Gbps)
Miljö Drifttemperatur 0°C to 40°C (32°F to 104°F)
Förvaringstemperatur -10°C to 65°C (14°F to 149°F)
Luftfuktighet Luftfuktighet vid användning: 10% ~ 90% RH
Luftfuktighet vid förvaring: 5% ~ 95% RH
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Maximal dataöverföringshastighet 10 Gbps
Typ och hastighet USB 3.1 Gen 2 - 10 Gbit/s
UASP-stöd Ja
4Kn Support Ja
Typ och hastighet SATA III (6 Gbps)
TRIM Support Ja
Medeltid mellan fel (MTBF) 1 000 000 timmar
Allmänna specifikationer Ej kompatibel med M.2 NVMe eller AHCI PCI-Express SSD-enheter
Ström Power Source Strömförsörjd via USB
Särskilda anmärkningar/krav Obs. Windows 7 and earlier Windows versions do not support TRIM with USB to SATA devices.
Utseende Produktvikt 61 g [2,2 oz]
Färg Svart & silver
Kabinettyp Aluminium
Maximal enhetshöjd 80 mm [3,1 in]
Produktlängd 99 mm [3,9 in]
Produktbredd 42 mm [1,7 in]
Produkthöjd 1,3 cm [0,5 in]
Vad det är i lådan 1 - Ingår i paketet M.2 NGFF SATA-kabinett - USB 3.1
USB-C till Micro B-kabel - 46 cm
M.2-skruvsats
Skruvmejsel
Snabbinstallationsguide

Tillbehör

USB31CUB1M

USB 3.1 USB-C till Micro-B-kabel - 1 m

Anslut USB Micro-B-enheter till din USB-C-värd med denna hållbara kabel på 1 meter

Ditt pris
€18,99 EUR excl. VAT
€23,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Inbyggd programvara

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive enclosure, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Cables
  • Hard drives
  • Hard drive enclosure

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive enclosure in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive enclosure in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive enclosure, it is recommended that you do the following:

  • To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.​

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

If your setup components support USB 3.1 but you are experiencing slower transfer speeds than you expected, consider the following:

  • A USB host connection with multiple USB 3.1 ports might not be able to support 10Gbps on each port simultaneously.
  • The type of port on a device does not determine whether the device is capable of USB 3.1 speeds. A USB-C port might not support USB 3.1 speeds, while USB-A and USB-B ports might support USB 3.1 speeds.
  • Any other devices that you include in your setup, such as an older hard drive in a USB 3.1 enclosure, might create a point of congestion and slow down transfer speeds.

To confirm the functionality of your USB host connection, its ports, and any other devices in your setup, refer to the information provided by the manufacturer.

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

Du bör inte uppgradera enhetens inbyggda programvara om du inte har några problem med enhetens funktioner. Du behöver bara uppgradera om du har problem med enheten och är säker på att problemet är den inbyggda programvaran.  Du kan bekräfta detta genom att läsa igenom den medföljande dokumentationen eller kontakta vår tekniska avdelning. Felaktig uppgradering av inbyggd programvara kan resultera i minskade prestanda så vi rekommenderar att du kontaktar StarTech.com först.

Hur man

To confirm that Windows detects your USB device, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Before You Buy

Although M.2 SSDs come in similar form factors, only an M.2 SATA drive with an NGFF B key will operate with this device. M.2 drives that are PCIe or have a different key position are not compatible with this device.

This device can adapt an M.2 SATA drive to standard SATA connections, which is not possible for a PCIe based M.2 drive. The key type refers to the connector type on the M.2 SATA drive. B key can be M.2 PCIe x2 or SATA, so it is important that you check the specifications of the drive to see if it supports SATA.

Yes, this device supports the TRIM command. If the OS issues a TRIM command, the command will be passed to the connected device.

To determine if your hard drive will work in this enclosure, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the enclosure supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the enclosure was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the enclosure. For example, IDE, SATA, or M.2.
  • Make sure that the enclosure supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Make sure that the enclosure supports the height of your hard drive. For example, 9 mm or 15 mm.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the enclosure. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the enclosure.

USB 3.1 is the most recent version of the USB (Universal Serial Bus) standard for connecting computers and electronic devices. It is capable of data transfer speeds up to 10Gbps, and while it can use the USB-C connector type, it can also use a variety of other connector types. To achieve USB 3.1 transfer speeds, your USB host connection, cables, and device must all support USB 3.1. USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). 

USB 3.0 is capable of data transfer speeds up to 5Gbps. USB 3.0 is also known as USB 3.1 Gen 1 (5Gbps).

USB 3.1 is backwards compatible with USB 3.0 and USB 2.0, except in the following scenarios:

  • USB-B 3.1 cables are not compatible with USB-B 2.0 ports.
  • Unless you use an adapter, USB-C ports or cables will not work with USB-A or USB-B ports or cables.
  • Devices that require USB 3.1 transfer speeds of 10Gbps might not work with USB 3.0 or USB 2.0, or you might experience lower transfer speeds and impacted performance.
  • Bus-powered USB devices that requires more power than what USB 2.0 can provide are not compatible with USB 2.0.

To transfer data at speeds of 10Gbps, you need to confirm that the following components in your setup support USB 3.1:

  • The USB host connection
  • The USB cable
  • The USB device and any subcomponents (for example, a hard drive docking station and the hard drives in the docking station)

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

The included USB cable for this USB 3.1 Gen 2 device has been tested and verified to perform at USB 3.1 Gen 2 speeds of 10Gbps.

USB-C is a type of USB connector that is capable of supporting the following:

  • Data transfer speeds up to 10Gbps, if you use USB 3.1.
  • Bi-directional power delivery up to 100W, if both the USB host connection and the device support it.
  • Alternate modes, which deliver different types of data at different speeds. For example, DisplayPort Alternate Mode (DP Alt Mode).

If using Thunderbolt 3 over USB-C, the connection is capable of additional features. For example, Thunderbolt 3 is capable of 40Gbps of total bandwidth. For more information, refer to the following FAQ: https://www.startech.com/faq/thunderbolt-3-port-capabilities.

Not all USB-C ports or devices are capable of supporting all of the features listed above, or all of the features at the maximum capabilities. If you require a specific USB-C feature, your USB host connection, cables, and device must all support the feature that you require. For more information about whether your components support specific USB-C features, refer to the information provided by the manufacturers. 

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen