Hårddiskkabinett med dubbla fack för mSATA SSD-enheter - USB 3.1 (10 Gbps) - RAID

Nå och säkerhetskopiera data snabbt från din USB-C- eller USB-A-kapabla enhet genom supersnabb USB 3.1 Gen 2

Produkt ID: SMS2BU31C3R

  • Maximera prestandan på dina mSATA SSD-enheter med USB 3.1 Gen 2-anslutning (10 Gbps)
  • Det dubbla mSATA RAID-kabinettet stöder mSATA och mSATA Mini (mSATA-hårddiskar i fullhöjd och halvhöjd)
  • Stöder RAID 0, RAID 1, JBOD och SPAN (BIG) för optimal prestanda, kapacitet och redundans
Ditt pris
€55,99 EUR excl. VAT
€69,99 EUR incl. VAT

Detta hårddiskkabinett med dubbla fack för mSATA- och mSATA mini-hårddiskar gör det enkelt att lägga till supersnabb, bärbar extern lagring till din bärbara dator, surfplatta eller stationära dator med USB-C™ eller USB-A. Det dubbla mSATA-kabinettet har även RAID-funktion för ökad kapacitet, förbättrad prestanda eller dataredundans.

Nå din externa data med högre hastighet

Nå, för över och säkerhetskopiera dina filer snabbt. Med det dubbla mSATA-kabinettet kan du utnyttja hastigheten från dina mSATA-hårddiskar genom att utnyttja USB 3.1 Gen 2 med dataöverföringshastigheter på upp till 10 Gbps. Det är idealiskt för IT-proffs, kreativa proffs, lärare, forskare och andra yrken där man behöver snabb åtkomst till viktiga datafiler, på kontoret, labbet eller från hemmet. USB 3.1 Gen 2 mSATA-kabinettet ger enkel åtkomst till dina filer för datamigrering och säkerhetskopiering så att du kan säkra data när som helst. 

Öka prestanda och dataredundans

Med flera RAID-alternativ kan du få ökad lagringsstorlek, prestanda, eller redundans. Njut av sinnesro och vetskapen att dina filer hela tiden säkerhetskopieras eller utnyttja den högre hastigheten och kapaciteten med en kombinerad lösning. Kabinettet stöder RAID 0, RAID 1, JBOD och SPAN (BIG) så att du kan välja det säkerhetskopieringsläge du föredrar. Det stöder även SSD TRIM för ökad livslängd och prestanda.

Få enkel bärbarhet

Kabinettet med två fack utnyttjar mSATA SSD-hårddiskars lilla formfaktor och hastigheten från USB 3.1 Gen 2 för att skapa en väldigt bärbar lagringslösning. Med kabinettet kan du lägga till två mSATA SSD-enheter externt till din bärbara eller stationära dator för snabb och bärbar datalagring. Det strömförses direkt från USB-porten på din enhet så att extern ström inte behövs. Med sin kompakta design kan du stoppa ner den i datorväskan och ta med den var som helst - från hemmet till kontoret, sjukhuset, labbet eller ut i fält, så att du kan nå din data var du än är.

Hårddiskkabinettet med dubbla fack är tillverkat med ett hölje i solitt aluminium för att skydda din data var du än är. Den levereras med två USB-kablar (USB-C till Micro-B och USB-A till Micro-B) för flexibel användning med de senaste bärbara datorerna och surfplattorna med en USB-Type C™-port samt äldre enheter och alla installationsverktyg som behövs. Kabinettet med två fack är dessutom kompatibel med en Thunderbolt™ 3 USB-C-port.

Kabinettet är OS-oberoende och behöver inte extra drivrutiner eller mjukvara. SMS2BU31C3R täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Lägg till bärbar extern lagring till din bärbara dator, surfplatta eller stationära dator med USB-C eller USB-A med hjälp av en mSATA- eller mSATA Mini-SSD
  • Få snabb åtkomst till viktiga datafiler genom supersnabb USB 3.1 Gen 2 (10 Gbps), idealiskt för kontorsproffs, försäljningschefer, lärare, forskare, vårdpersonal och andra mobila arbetare
  • Återanvänd eller få ny användning av hårddiskar för att få mer PC-lagring eller för att säkerhetskopiera data
  • Idealisk för att skydda hårddiskar mot damm och andra potentiella faror
  • Få åtkomst till hårddiskar för dataåterställning, säkerhetskopiering eller reparation

Partnernummer

  • UPC 065030866880

Kompatibilitet

  • OS Independent logo
OS independent; No software or drivers required

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Fraktvikt (förpackning) 202 g [7,1 oz]
Package Length 16 cm [6,3 in]
Package Width 13 cm [5,1 in]
Package Height 30 mm [1,2 in]
Hårdvara Gränssnitt USB 3.1 Gen 2
Busstyp USB 3.1 Gen 2
Antal enheter 2
Enhetsstorlek mSATA (Full Size & Half Size)
Enhetstyp mSATA (Mini SATA)
Enhetsinstallation Fixed
Stödda enhetshöjd(er) Full Size (50.8mm)
Half Size (26.8mm)
Fläkt(ar) No
Chipset-ID ASMedia - ASM1352R
Indikatorer 2 - LED-indikatorer Läsa/skriva (vitt)
Fel/ombyggt (röd)
Kontakt(er) 2 - Enhetskontakter mSATA (52 pin, Mini SATA) Slot
1 - Värdkontakter USB 3.1 USB Type Micro-B (10 pin, Gen 2, 10 Gbps)
Miljö Drifttemperatur 0°C to 50°C (32°F to 122°F)
Förvaringstemperatur -10°C to 85°C (14°F to 185°F)
Luftfuktighet 5 % ~ 95 %
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Maximal dataöverföringshastighet 10 Gbps
Typ och hastighet USB 3.1 Gen 2 - 10 Gbit/s
UASP-stöd Yes
4Kn Support Yes
Typ och hastighet SATA III (6 Gbps)
Port Multiplier Yes
TRIM Support Yes
RAID Yes
RAID-lägen som stöds RAID 0 (Striped Disks)
RAID 1 (Mirrored Disks)
JBOD - (Just a Bunch of Disks)
BIG (Spanning or Concatenation)
Medeltid mellan fel (MTBF) 5 000 000 timmar
Ström Power Source USB-Powered
Särskilda anmärkningar/krav Obs. Windows 7 and earlier Windows versions do not support TRIM with USB to SATA devices.
Utseende Färg Black
Kabinettyp Aluminum
Produktlängd 10 cm [3,9 in]
Produktbredd 80 mm [3,1 in]
Produkthöjd 1,6 cm [0,6 in]
Produktvikt 100 g [3,5 oz]
Vad det är i lådan 1 - Ingår i paketet hårddiskkabinett med dubbla fack
USB-C till Micro-B-kabel - 46 cm
USB-A till Micro-B-kabel - 46 cm
Skruvmejsel
snabbstartsguide
2 - Ingår i paketet set med mSATA-monteringsutrustning
4 - Ingår i paketet monteringsskruvar för hölje

Tillbehör

USB31CUB1M

USB 3.1 USB-C till Micro-B-kabel - 1 m

Anslut USB Micro-B-enheter till din USB-C-värd med denna hållbara kabel på 1 meter

Ditt pris
€18,99 EUR excl. VAT
€23,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive enclosure, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Cables
  • Hard drives
  • Hard drive enclosure

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive enclosure in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive enclosure in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive enclosure, it is recommended that you do the following:

  • To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.​

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

In order to rebuild a RAID array, you need to replace a physical drive with an identical drive on the same RAID controller. Although standard RAID levels are generally agreed upon throughout the industry, the implementation varies between manufacturers. RAID arrays are typically not accessible when they are moved to another controller, and data may be unrecoverable if the drives are out of order or have been formatted or accessed by another RAID controller.

If a RAID controller has failed, you should get the exact same model of RAID controller.  

Note: If a drive or drives were damaged, it is possible that the RAID array may be permanently unrecoverable.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, you should back up the data on another physical drive or logical set of drives.

Rebuild a RAID array

With the following RAID modes, recovery is possible using the same StarTech.com product. Refer to the following table for the appropriate method to use to recover your RAID array.

RAID mode Max # of failed drives Procedure
RAID 1 Only one drive is needed for recovery.
  1. Determine which drive is operational by using the RAID management utility (if available) or test each drive individually on a different hard drive controller (for example, a hard drive docking station or SATA controller).

  2. Replace the failed drive with an identical hard drive.

The array will rebuild and is accessible during the rebuilding process.

RAID 3 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 5 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 10 Only one drive in a mirrored set can fail.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

 

If your setup components support USB 3.1 but you are experiencing slower transfer speeds than you expected, consider the following:

  • A USB host connection with multiple USB 3.1 ports might not be able to support 10Gbps on each port simultaneously.
  • The type of port on a device does not determine whether the device is capable of USB 3.1 speeds. A USB-C port might not support USB 3.1 speeds, while USB-A and USB-B ports might support USB 3.1 speeds.
  • Any other devices that you include in your setup, such as an older hard drive in a USB 3.1 enclosure, might create a point of congestion and slow down transfer speeds.

To confirm the functionality of your USB host connection, its ports, and any other devices in your setup, refer to the information provided by the manufacturer.

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

Before You Buy

To determine if your hard drive will work in this enclosure, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the enclosure supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the enclosure was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the enclosure. For example, IDE, SATA, or M.2.
  • Make sure that the enclosure supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Make sure that the enclosure supports the height of your hard drive. For example, 9 mm or 15 mm.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the enclosure. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the enclosure.

Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.

Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.

The following are terms that are normally used in connection with RAID:

  • Striping: data is split between multiple disks.
  • Mirroring: data is mirrored between multiple disks.
  • Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.

Different RAID levels exist for different application requirements.

Refer to the following table for the list of RAID modes offered by some StarTech.com products:

RAID mode Description Operation Advantages Disadvantages Recovery
RAID 0 Striped disks Data is split evenly between two or more disks. Large size and the fastest speed. No redundancy. If one or more drives fails, this results in array failure.
RAID 1 Mirrored disks Two or more drives have identical data on them. A single drive failure will not result in data loss. Speed and size is limited by the slowest and smallest disk. Only one drive is needed for recovery.
RAID 3 Striped set with dedicated parity Data is split evenly between two or more disks, plus a dedicated drive for parity storage. High speeds for sequential read/write operations. Poor performance for multiple simultaneous instructions. A single drive failure will rebuild.
RAID 5 Striped disks with distributed parity Data is split evenly between three or more disks. Parity is split between disks. Large size, fast speed, and redundancy. The total array size is reduced by parity. A single drive failure will rebuild.
RAID 10 1+0; Striped set of Mirrored Subset Four or more drives are made into two mirrors that are striped. Larger size and higher speed than RAID-1, and more redundancy than RAID-0. No parity. Only one drive in a mirrored set can fail.
JBOD Just a Bunch Of Disks Any number of drives are accessed independently by the operating system. Software RAID modes can be used. Hardware RAID may have better performance. N/A
Big Spanning or Concatenation Data is written on one drive until it is full, and then the next drive(s) until it or they are full. Creates a very large and simple array.

No redundancy.

N/A
Clone RAID 1 + Spare

Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure.

Seamless operation when one drive fails in a RAID-1 array. Spare drive is not accessible to the user. Only one drive is needed for recovery.

 

USB 3.1 is the most recent version of the USB (Universal Serial Bus) standard for connecting computers and electronic devices. It is capable of data transfer speeds up to 10Gbps, and while it can use the USB-C connector type, it can also use a variety of other connector types. To achieve USB 3.1 transfer speeds, your USB host connection, cables, and device must all support USB 3.1. USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). 

USB 3.0 is capable of data transfer speeds up to 5Gbps. USB 3.0 is also known as USB 3.1 Gen 1 (5Gbps).

USB 3.1 is backwards compatible with USB 3.0 and USB 2.0, except in the following scenarios:

  • USB-B 3.1 cables are not compatible with USB-B 2.0 ports.
  • Unless you use an adapter, USB-C ports or cables will not work with USB-A or USB-B ports or cables.
  • Devices that require USB 3.1 transfer speeds of 10Gbps might not work with USB 3.0 or USB 2.0, or you might experience lower transfer speeds and impacted performance.
  • Bus-powered USB devices that requires more power than what USB 2.0 can provide are not compatible with USB 2.0.

To transfer data at speeds of 10Gbps, you need to confirm that the following components in your setup support USB 3.1:

  • The USB host connection
  • The USB cable
  • The USB device and any subcomponents (for example, a hard drive docking station and the hard drives in the docking station)

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

The included USB cable for this USB 3.1 Gen 2 device has been tested and verified to perform at USB 3.1 Gen 2 speeds of 10Gbps.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen