Hårddiskduplikator och -raderare för USB-minnen och 2,5/3,5" SATA-hårddiskar

Duplicera eller radera ett USB-minne eller en SATA SSD/HDD, med 1:1 och gränssnittsöverskridande duplicering

Produkt ID: SU2DUPERA11

  • Duplicera eller radera 2,5/3,5" SATA SSD/HDD-enheter och USB-ansluten lagring
  • 1:1 duplicering plus gränssnittsöverskridande stöd: SATA-till-USB eller USB-till-SATA
  • Stöder fyra lägen för hårddisk-duplikation inklusive sektor-för-sektor med 6,6 GB/min
Ditt pris
€919,99 EUR excl. VAT
€1 149,99 EUR incl. VAT

Med denna mångsidiga hårddisk-duplikator och -raderare kan du klona och radera både USB-baserade lagringsenheter och 2,5" och 3,5" SATA SSD- och HDD-enheter, utan att behöva ansluta till en dator. Denna mångsidiga enhet är idealisk för IT-proffs och systemadministratörer och hjälper dig hantera din fil- och datalagring effektivare och ger både 1:1 kopiering och gränssnittsöverskridande duplikation.

1:1 eller gränssnittsöverskridande duplikation av SATA- eller USB-enheter

Som en hårddisk-klonare låter enheten dig enkelt kopiera SATA- och USB-enheter utan att behöva ansluta till en dator. Den låter dig duplicera 1:1 (från SATA till SATA eller USB till USB) samt gränssnittsöverskridande duplikation från SATA till USB eller USB till SATA. Hårddisk-klonaren har fyra dupliceringslägen, inklusive snabbkopiering, alla partitioner, sektor-för-sektor (hela hårddisken) med hastigheter på upp till 6,6 GB/min och procentkopiering.

Flera raderingslägen

Radera enkelt SATA- eller USB-enheter utan en värddator. Som en hårddisk-raderare har SU2DUPERA11 sex raderingslägen inklusive snabbradering, single pass-överskrivning (full radering), 3-pass-överskrivningsradering (DoD), 3-Pass-överskrivning och -jämförelse, säker radering och 7-pass-överskrivning. Du kan radera en enda SATA eller USB-enhet eller två enheter samtidigt.

Designad för enkel användning

Hårddisk-duplikatorn och -raderaren har en kompakt och lätt design med lättanvända funktioner. Den har enkla knappar för menynavigering och en LCD-display som tydligt identifierar aktivt duplicerings- eller raderingsläge och status för att garantera snabb och effektiv användning.

SU2DUPERA11 täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Kriminaltekniker som behöver ha speglingar/kloningar för att skapa en exakt kopia av källdisken på en annan hårddisk.
  • Yrkesverksamma som behöver identiska säkerhetskopior när det är av yttersta vikt att datan är komplett, som till exempel vid dataåterställning
  • Klona hårddiskar som innehåller dolda partitioner som vissa program för hårddisk-kloning hoppar över
  • IT-administratörer som vill tömma/radera en hårddisk snabbt för att kunna använda den i andra situationer
  • Radera/töm data säkert på din hårddisk innan hårddisken kasseras

Partnernummer

  • UPC 065030865005

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Fraktvikt (förpackning) 1,9 kg [4,2 lb]
Package Length 26,5 cm [10,4 in]
Package Width 18,5 cm [7,3 in]
Package Height 10 cm [3,9 in]
Hårdvara Antal enheter 2
Enhetsstorlek 2.5in & 3.5in
Enhetstyp SATA
USB-minne
Fläkt(ar) Nej
Chipset-ID Xilinx - Spartan-6
Indikatorer 4 - LED-indikatorer Ström/aktivitet
Hårddisk-anslutning
Enhetsfel
Kontakt(er) 2 - Enhetskontakter 22 pin SATA Data + Power (7 + 15 pin) Receptacle
USB Type-A (4-stifts) USB 2.0
Miljö Drifttemperatur 5°C ~ 45°C (41°F ~ 113°F)
Förvaringstemperatur -20°C ~ 85°C (-4°F ~ 185°F)
Luftfuktighet 5% ~ 95% RH
Prestanda 4Kn Support Ja
Port Multiplier Nej
Duplication Modes System and File
All Partitions
Sector by Sector (Whole Drive)
Percentage Copy
Duplication Speed 6.6GBpm
Raderingslägen Quick Erase
1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear)
3-Pass Overwrite
3-Pass Erase and Compare
Custom Erase
Maximal enhetskapacitet 2 TB för USB och ingen känd gräns för SATA
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 1.4A
Utspänning 12V DC
Utström 5A
Polaritet på mittpol Positiv
Kontakttyp M
Strömförbrukning 60
Utseende Färg Svart
Kabinettyp Stål
Produktlängd 13,5 cm [5,3 in]
Produktbredd 90 mm [3,5 in]
Produkthöjd 2,9 cm [1,1 in]
Produktvikt 462 g [16,3 oz]
Vad det är i lådan 1 - Ingår i paketet SATA/USB-duplikator och -raderare
universell strömadapter (NA/JP, UK, EU, AU)
snabbstartsguide
2 - Ingår i paketet anslutningskablar för hårddisk
hårddiskkuddar

Tillbehör

HDDSLEV35

3,5" skyddshylsa i silikon med kontaktlock för hårddiskar

Skydda en 3,5" hårddisk mot elstötar/sammanstötningar

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25YW

2.5in Anti-Static Hard Drive Protector Case - Yellow (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25GN

2.5in Anti-Static Hard Drive Protector Case - Green (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
HDDCASE25BK

2,5" antistatiskt skyddsfodral för hårddiskar - Svart (3-pack)

Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet

Ditt pris
€19,99 EUR excl. VAT
€24,99 EUR incl. VAT
Utgått
HDDCASE25OR

2.5in Anti-Static Hard Drive Protector Case - Orange (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
25SATSAS35

2,5" SATA/SAS SSD/HDD till 3,5" SATA-hårddisk-konverterare

Omvandlar i stort sett alla 2,5 tums SATA- och SAS-hårddiskar till en 3,5 tums SATA-hårddisk

Ditt pris
€22,99 EUR excl. VAT
€28,74 EUR incl. VAT
SAT2MSAT25

2,5" SATA till mini SATA-SSD-adapterhölje

Konvertera en mSATA mini-SSD till en vanlig 2,5" SATA-SSD

Ditt pris
€38,99 EUR excl. VAT
€48,74 EUR incl. VAT
Utgått
SAT2CF

SATA to Compact Flash SSD Adapter

Turn a Compact Flash card into a bootable SATA SSD

Ditt pris
€40,99 EUR excl. VAT
€51,24 EUR incl. VAT
HDDSLEV25

2.5in Silicone Laptop Hard Drive Protector Sleeve with Connector Cap

Provide protection against shocks/impacts to a 2.5in hard drive

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
Utgått
HDDCASE25BL

2.5in Anti-Static Hard Drive Protector Case - Blue (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25WH

2.5in Anti-Static Hard Drive Protector Case - White (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
SAT2IDEADP

SATA till 2,5" eller 3,5" IDE-hårddisk-adapter för HDD-dockningsstationer

Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
USBEXTAA6IN

15 cm USB 2.0-förlängningsadapterkabel A till A - M/F

Förlänger din nuvarande USB-kabel med 15 centimeter

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
USB3EXT6INBK

USB 3.0 A-till-A förlängningskabel – 15 cm, svart

Utöka din USB 3.0-ports räckvidd med 15 cm

Ditt pris
€5,99 EUR excl. VAT
€7,49 EUR incl. VAT
SVA12M5NA

DC-strömadapter - 12 V, 5 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€65,99 EUR excl. VAT
€82,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

SATA hard drive controllers require a feature called port multiplier to read more than one hard drive per SATA or eSATA port. The port multiplier feature is not standard on many SATA hard drive controllers.

If your computer is only recognizing one of your hard drives, you need to plug the eSATA cable into a SATA controller that includes the port multiplier feature. If none of your current hard drive controllers include this feature, you can add a hard drive controller that does support port multiplier in any available expansion slot (for example, PCI, PCI-Express, PCMCIA, CardBus, or ExpressCard). StarTech.com has hard drive controllers available that support the port multiplier feature. To view the hard drive controllers, click here: http://startech.com/Cards-Adapters/HDD-Controllers/SATA-Cards/?filter_PORTMULTIPLIER=Yes.

If you have a hard drive controller card that does support the port multiplier feature but it is only reading one hard drive at a time, update the drivers of the hard drive controller. To find the most current StarTech.com drivers, click here: http://www.startech.com/Support.

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.

Before You Buy

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.

Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen