Utgått

USB till SATA IDE dockningsstation för 2,5" eller 3,5" HDD

Anslut både en IDE- och SATA-hårddisk till en dator genom USB 2.0

Produkt ID: UNIDOCK2U

  • SATA-enhetskontakt med inmatning upptill
  • Frontpanel IDE data och strömkontakter
  • Patenterad mekanism för enhetsutmatning

UNIDOCK2U HDD-dockningsstation ger full, omedelbar åtkomst till en 2,5" och/eller 3,5" IDE- eller SATA-hårddisk utan att behöva montera enheten i en dator eller installera den i ett externt kabinett. Hårddiskar med stor kapacitet (testat med upp till 4 TB 3,5"- och 1 TB 2,5"-hårddiskar) kan användas för att betydligt öka dina datorers lagrings-/säkerhetskopieringskapacitet.

Anslut värddatorn via en enda USB 2.0-anslutning. Både IDE- och SATA-hårddisken kan (SATA, SATA II, SATA III) anslutas till HDD-dockan på samma gång - en smidig lösning för att överföra data från en IDE- till en SATA-hårddisk eller tvärtom, eller helt enkelt för att ha snabb och enkel åtkomst till båda hårddiskarnas innehåll.

Hårddisk-dockningsstationen är en idealisk lösning för alla datorapplikationer, med stöd för plug-and-play-installationer av hårddiskar med de flesta operativsystemen för att garantera enkel hårddiskväxling och bekväm åtkomst till värdefull data.

Användning

  • Överför filer direkt mellan en SATA- och IDE-hårddisk, utan att behöva föra över till värddatorn först eller använda flera enheter
  • Snabb åtkomst till 2,5/3,5"-enheter att hämta data från
  • För dataåterställningsspecialister som snabbt behöver komma åt enheter för säkerhetskopiering
  • Säkerhetskopiera data snabbt till en extern hårddisk för arkivering
  • Tekniker som testar eller utvärderar flera hårddiskar

Fördelarna med StarTech.com

  • Anslut en SATA- och IDE-hårddisk samtidigt till en dator eller separat, genom en enda USB 2.0-anslutning
  • Designen med kortplatsinmatning och den unika enhetsutmatningsmekanismen ger en snabb och enkel åtkomst till data utan att behöva installera drivrutiner till ett kabinett eller fack.
  • Täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support

Partnernummer

  • UPC 065030836708

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Length 15.8 cm [6.2 in]
Package Width 12 cm [4.7 in]
Package Height 16.5 cm [6.5 in]
Fraktvikt (förpackning) 1.1 kg [2.4 lb]
Hårdvara Gränssnitt USB 2.0
Antal enheter 2
Enhetsstorlek 2.5in & 3.5in
Enhetstyp SATA & IDE
Enhetsinstallation Löstagbar
Fläkt(ar) Nej
Chipset-ID JMicron - JM20337
Indikatorer 1 - LED-indikatorer Ström och enhetsaktivitet
Kontakt(er) 1 - Enhetskontakter SATA-ström (15-stifts)
SATA (7-stifts, data)
IDE (44-stifts, EIDE/PATA, 2,5" HDD)
LP4 (4-stift, Molex-type Large Drive Power)
IDE (40-stifts, EIDE/PATA)
1 - Värdkontakter USB B (4-stifts)
Miljö Drifttemperatur 5°C to 80° (41°F to 176°F)
Förvaringstemperatur -40°C to 70°C (-40°F to 158°F)
Luftfuktighet 8~90 % RH
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Typ och hastighet USB 2.0 - 480 Mbit/s
UASP-stöd Nej
Maximal enhetskapacitet För närvarande testat med upp till 4 TB 5400 rpm 3,5"-hårddiskar och 1 TB 5400 rpm 2,5"-hårddiskar
Inlänkningshastighet 15,000 Cycles
Ström Power Source AC-adapter medföljer
Inspänning 110V-240V AC
Utspänning 12V DC
Utström 3A
Polaritet på mittpol Positiv
Kontakttyp M
Utseende Färg Svart
Kabinettyp Av plast
Produktlängd 14.5 cm [5.7 in]
Produktbredd 93 mm [3.7 in]
Produkthöjd 65 mm [2.6 in]
Produktvikt 413 g [14.6 oz]
Vad det är i lådan 1 - Ingår i paketet Universell SATA IDE USB 2.0 hårddisk-dockningsstation
40 stifts + LP4 till 44 stifts IDE-kabel
LP4 Strömkabel
IDE 40 till 40-stifts kabel
USB 2.0-kabel
3 - Ingår i paketet Strömkabel
1 - Ingår i paketet Universell strömadapter
Instruktionsbok

Tillbehör

SAT2IDEADP

SATA till 2,5" eller 3,5" IDE-hårddisk-adapter för HDD-dockningsstationer

Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
Utgått
IDE4044

2.5in to 3.5in IDE Hard Drive Cable Adapter

Connect a 2.5in IDE laptop hard drive to an IDE-equipped desktop computer.

Ditt pris
€5,99 EUR excl. VAT
€7,49 EUR incl. VAT
Utgått
PCI330USB2

4 Port PCI High Speed USB 2.0 Adapter Card

Add 4 USB 2.0 ports to a computer through a PCI slot

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
Utgått
PCI420USB

5 Port PCI High Speed USB 2.0 Adapter Card

Add 5 USB 2.0 ports to any desktop computer with a PCI slot

Ditt pris
€16,99 EUR excl. VAT
€21,24 EUR incl. VAT
Utgått
PEX400USB2

PCI Express USB 2.0-kortadapter med 5 portar

Lägg till 4 externa USB-portar och 1 intern USB-port till din dator genom en PCI-Express-plats

Ditt pris
€51,99 EUR excl. VAT
€64,99 EUR incl. VAT
HDDSLEV35

3,5" skyddshylsa i silikon med kontaktlock för hårddiskar

Skydda en 3,5" hårddisk mot elstötar/sammanstötningar

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
HDDSLEV25

2.5in Silicone Laptop Hard Drive Protector Sleeve with Connector Cap

Provide protection against shocks/impacts to a 2.5in hard drive

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
Utgått
EC400USB

4 Port ExpressCard Laptop USB 2.0 Adapter Card

Add 4 USB 2.0 ports to a laptop from an ExpressCard slot

Ditt pris
€16,99 EUR excl. VAT
€21,24 EUR incl. VAT
Utgått
CB420USB

4 Port CardBus Laptop USB 2.0 PC Card Adapter

Adds 4 USB 2.0 ports to an older laptop with a CardBus slot

Ditt pris
€33,99 EUR excl. VAT
€42,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size

If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.

When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.

There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

Hur man

To confirm that Windows detects your USB device, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Before You Buy

Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.

Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.

There are a number of reasons that older IDE drives may not be detected, including the following:

  • The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).

  • The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).

  • The sector size is not 512 bytes.

Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen
Vänta...