PCI Express 2.0 SATA III 6 Gbps RAID-kontrollerkort med 4 portar och HyperDuo nivåindelad SSD-lagring

Lägg till 4 interna SATA III-portar (6 Gbps) till datorn genom en PCI Express x2-kortplats

Produkt ID: PEXSAT34RH

  • Stöder automatisk nivåindelad SSD-datalagring med HyperDuo
  • 4 AHCI SATA III-portar (6 Gbps) genom PCI express x2
  • Fullt kompatibelt med specifikationer för SATA 3.0 och bakåtkompatibelt med SATA I/II-enheter (1,5/3,0 Gbps)
Ditt pris
€107,99 EUR excl. VAT
€134,99 EUR incl. VAT

PEXSAT34RH SATA-kontrollerkort med 4 portar och HyperDuo för PCI express 2.0 lägger till 4 AHCI SATA III-portar till en dator genom en PCI-kortplats (x2) och ger flera interna anslutningar på 6 Gbps för högpresterande hårddiskar och solid state-enheter (SSD).

SATA-kortet har HyperDuo och ger automatisk nivåindelad SSD-datalagring som ger dig den perfekta blandningen av prestanda från SSD-lagring och kostnadseffektiviteten och den höga kapaciteten från vanliga hårddiskar. Genom att kombinera SSD- och HDD-enheter till en enda volym (upp till 3 SSD + 1 HDD) arbetar HyperDuo diskret i bakgrunden för att identifiera och flytta filer som används ofta till de snabbare SSD-enheterna för snabbare datagenomströmning; upp till 80 % av SSD-prestandan! (Obs.: Den automatiska nivåindelade datalagringen från HyperDuo är kompatibel med datorer som använder BIOS.)

SATA-kontrollerkortet för PCIe stöder portmultiplicering (PM) och låter flera SATA-enheter anslutas till en port med en enda kabel för totalt 7 enheter (upp till 4 enheter genom PM på en port och en enda enhet till de resterande 3 portarna). SATA-kontrollerkortet har dessutom en effektiv RAID-lösning med ursprungligt RAID-stöd (0, 1, 1+0).


Prestandamått på genomströmning

Enhetskonfiguration Genomströmning Enhetsstorlek
1 x HDD 112.81 MB/s 2 TB
1 x SSD 490,28 MB/s 120 GB
1 x HDD + 1 x SSD HyperDuo (felsäkert läge) 489.28 MB/s 2 TB
1 x HDD + 2 x SSD HyperDuo (felsäkert läge) 715.13 MB/s 2 TB
Enheter som används:
SSD: OCZ Vertex 3 Series 2,5" 120 GB (VTX3-25SAT3-120G)
HDD: Western Digital Caviar Green 3,5" 2 TB (WD20EARS)

Mjukvara som används:
IO Meter, 256 kB sekventiell läsning, ködjup = 10

Detta SATA-kort för PCIe täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Använd nivåindelad SSD-datalagring för att optimera systemet för I/O-intensiva program som Office-paketet, foto-/videoredigeringsprogram och mediaspelare
  • Lägg till flera interna SATA-portar till en dator för att ansluta extra lagringsenheter och/eller optiska enheter
  • Uppgradera ett äldre PCIe-baserat system till 6 Gbps SATA för att få bättre användning av SATA-enheter
  • Perfekt lösning för RAID-lagring med flera enheter
  • Ger optimerad extern säkerhetskopiering/-lagring med inbyggd RAID 1

Fördelarna med StarTech.com

  • Få SSD-prestanda och kapaciteten från en vanlig HDD med HyperDuo-teknik
  • Maximera systemets förmågor med anslutningshastigheter från SATA III
  • Passar i alla chassin i standardutförande eller lågprofil med medföljande fästen

Partnernummer

  • Ingram Micro Sweden V932280
  • ALSO Sweden 000000000002764069
  • UPC 065030849951

Kompatibilitet

  • Windows 7 logo
  • Linux logo
  • Windows 8 logo
  • Windows 10 logo
  • Mac OS X El Capitan (10.11) logo
  • macOS Sierra (10.12) logo
  • Windows Server 2012 logo
  • macOS High Sierra (10.13) logo
  • Windows Server 2016 logo
  • macOS Mojave (10.14) logo
  • Windows Server 2019 logo
Windows® XP, Vista, 7, 8, 8.1, 10
Windows Server® 2003, 2008 R2, 2012, 2012 R2, 2016
Mac OS® 10.6 till 10.14
Linux 3.5.x till 4.11.x Endast LTS-versioner

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 32 mm [1.3 in]
Package Length 17.5 cm [6.9 in]
Fraktvikt (förpackning) 141 g [5.0 oz]
Package Width 14.5 cm [5.7 in]
Förpackningsantal 1
Hårdvara Portar 4
Gränssnitt SATA
Busstyp PCI Express
Korttyp Standardprofil (inkl. LP-fäste)
Porttyp Inbyggd på kort
Industristandarder PCI Express 2.0
Specifikationen för seriell ATA 3.0
Chipset-ID Marvell - 88SE9230
Kontakt(er) 4 - Interna portar SATA (7-stifts, data)
1 - Kontakttyp(er) PCI Express x2
Miljö Drifttemperatur 5°C ~ 50°C (41°F ~ 122°F)
Förvaringstemperatur -25°C ~ 70°C (-13°F ~ 158°F)
Luftfuktighet 20% ~ 80% RH
Mjukvara OS-kompatibilitet Windows® XP, Vista, 7, 8, 8.1, 10
Windows Server® 2003, 2008 R2, 2012, 2012 R2, 2016
Mac OS® 10.6 till 10.14
Linux 3.5.x till 4.11.x Endast LTS-versioner
Prestanda RAID-lägen som stöds JBOD - (Just a Bunch of Disks)
RAID 1 (speglade enheter)
RAID 0 (stripade enheter)
RAID 10 (1+0, Stripat set av speglade enheter)
Typ och hastighet SATA III (6 Gbps)
Port Multiplier Ja
Number of Ports That Support Port Multiplier 4 (can only use 1 PM at a time)
Number of Drives Supported Through Port Multiplier 1 to 4
Bootable Ja
LBA-stöd 48-bit
RAID Ja
ATAPI Support Ja
Maximal enhetskapacitet För närvarande testad med upp till 4 TB per enhet
Hot swap-förmåga Ja
Särskilda anmärkningar/krav System- och kabelkrav Tillgänglig PCI express x2-kortplats (bakåtkompatibel med x4, x8 och x16)
Obs.

Kortets maximala datagenomströmning begränsas av bussens gränssnitt. Vid användning med PCI express Gen 1.0-kapabla datorer är den maximala genomströmningen 2.5 Gbps per bana. Vid användning med PCI express Gen 2.0-kapabla datorer är den maximala genomströmningen 5 Gbps per bana.

Endast en port kan använda port-multipliceringsfunktionen åt gången. Stöder upp till 4 enheter anslutna via portmultiplicering, totalt 7 enheter.

Portmultiplicering stöds ej av Mac OS.

Obs: Anslutna enheter kan inte användas som system/primär enhet i Windows Server 2012, 2012 R2, 2016

Marvell Storage Utility-applikationen kräver macOS 10.9 till 10.14.

Utseende Produktvikt 49 g [1.7 oz]
Kabinettyp Stål
Produktlängd 70 mm [2.8 in]
Produktbredd 12 cm [4.7 in]
Produkthöjd 20 mm [0.8 in]
Vad det är i lådan 1 - Ingår i paketet PCIe SATA-kontrollerkort
Lågprofilsfäste
Drivrutin CD
Instruktionsbok

Tillbehör

Utgått
SATSASBAY425

2,5" löstagbara SAS SATA flyttbara bakpanelställ för 4 enheter

Installera fyra 2,5 tums SAS/SATA-hårddiskar i ett 5,25 tums enhetsfack

Ditt pris
€85,99 EUR excl. VAT
€107,49 EUR incl. VAT
HSB430SATBK

4 enheter 3,5" hyllfri hot swap SATA med flyttbara bakpanelshyllor

Hot swapa upp till fyra 3,5" SATA-hårddiskar på sekunder

Ditt pris
€121,99 EUR excl. VAT
€152,49 EUR incl. VAT
Utgått
HSB320SATBK

3 Drive 3.5in Trayless Hot Swap SATA Mobile Rack Backplane

Hot swap up to three 3.5in SATA hard drives in seconds

Ditt pris
€89,99 EUR excl. VAT
€112,49 EUR incl. VAT
Utgått
DRW115SATBK

5,25" professionell SATA-hårddisk flyttbar ställåda i svart aluminium

Byt SATA-hårddiskar på PC eller server, snabbt och enkelt

Ditt pris
€70,99 EUR excl. VAT
€88,74 EUR incl. VAT
Utgått
HSB225SATBK

3,5" hyllfri hot swap SATA flyttbart ställ för dubbla 2,5" hårddiskar

Anslut och byt ut två 2,5 tums SATA-hårddiskar eller SSD:er enkelt via ett enda 3,5 tums-frontpanelsfack

Ditt pris
€50,99 EUR excl. VAT
€63,74 EUR incl. VAT
LSATA8

8in Latching SATA to SATA Cable - F/F

Secure latching SATA cable designed for new system boards and SATA hard drives

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
LSATA12

30 cm SATA-kabel med lås

SATA-kontakter med lås, för säkert fastsatta hårddiskinstallationer.

Ditt pris
€2,99 EUR excl. VAT
€3,74 EUR incl. VAT
LSATA18

45 cm SATA-kabel med lås

SATA-hårddiskkabel med låsbara SATA-kontakter, ger hårddiskinstallationer som sitter säkert.

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
SATA18RA1

45 cm SATA till högervinklad SATA seriell ATA-kabel

Anslut din SATA-enhet i rät vinkel vid installation i trånga utrymmen

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
Utgått
SATARA18

18in Right Angle SATA Cable - F/F

Make a right-angled connection to your SATA drive, for installation in tight spaces

Ditt pris
€1,99 EUR excl. VAT
€2,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Inbyggd programvara

Manual(er):

Mjukvara

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

Before you install the device, make sure that your operating system is current (for example, the most recent service pack is installed).

  1. Download the latest drivers from the StarTech.com website at http://www.startech.com/Support. The part number and product ID are on the product packaging.

Note: Windows usually saves the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. After the download is complete, right-click the zip folder that you downloaded, click Extract All, and complete the instructions.
  2. In the list of extracted files, right-click the Setup.exe file and click Run as Administrator.

Note: If the Run as Administrator option is not available, you might be attempting to run the installer from within the zipped file. Extract the files using the instructions in step 2.

  1. Complete the instructions to install the device drivers, and restart your computer when prompted to.

Your computer will automatically complete the driver installation and your device should be ready to use.

Before you install the device, make sure that your operating system is current (for example, the most recent service pack is installed).

  1. Download the latest drivers from the StarTech.com website at http://www.startech.com/Support. The part number and product ID are on the product packaging.

Note: Windows usually saves the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. After the download is complete, right-click the zip folder that you downloaded, click Extract All, and complete the instructions.
  2. In the list of extracted files, double-click the Setup.exe file.
  3. Complete the instructions to install the device drivers, and restart your computer when prompted to.

Your computer will automatically complete the driver installation and your device should be ready to use.

Problemsökning

When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables

  • Hard drives

  • Hard drive controller card

To test your setup components, try the following:

  • Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.

  • Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the hard drive and hard drive controller card, it is recommended that you do the following:

  1. To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.

  2. Do one of the following:

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.

  2. If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.

In order to rebuild a RAID array, you need to replace a physical drive with an identical drive on the same RAID controller. Although standard RAID levels are generally agreed upon throughout the industry, the implementation varies between manufacturers. RAID arrays are typically not accessible when they are moved to another controller, and data may be unrecoverable if the drives are out of order or have been formatted or accessed by another RAID controller.

If a RAID controller has failed, you should get the exact same model of RAID controller.  

Note: If a drive or drives were damaged, it is possible that the RAID array may be permanently unrecoverable.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, you should back up the data on another physical drive or logical set of drives.

Rebuild a RAID array

With the following RAID modes, recovery is possible using the same StarTech.com product. Refer to the following table for the appropriate method to use to recover your RAID array.

RAID mode Max # of failed drives Procedure
RAID 1 Only one drive is needed for recovery.
  1. Determine which drive is operational by using the RAID management utility (if available) or test each drive individually on a different hard drive controller (for example, a hard drive docking station or SATA controller).

  2. Replace the failed drive with an identical hard drive.

The array will rebuild and is accessible during the rebuilding process.

RAID 3 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 5 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 10 Only one drive in a mirrored set can fail.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

 

Du bör inte uppgradera enhetens inbyggda programvara om du inte har några problem med enhetens funktioner. Du behöver bara uppgradera om du har problem med enheten och är säker på att problemet är den inbyggda programvaran.  Du kan bekräfta detta genom att läsa igenom den medföljande dokumentationen eller kontakta vår tekniska avdelning. Felaktig uppgradering av inbyggd programvara kan resultera i minskade prestanda så vi rekommenderar att du kontaktar StarTech.com först.

Hur man

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your expansion card, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your expansion card is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

In order to use a hard drive plugged into a hard drive controller card as your operating system, you need to install the operating system onto the hard drive while it is plugged into the expansion card. To do this, complete the following:

Note: Not all hard drive controller cards have drivers that allow you to install the operating system onto the hard drive. All of the hard drive controllers that display this FAQ include this capability.

Before you begin, consult the documentation that came with the motherboard to make sure that the motherboard or BIOS supports booting from an expansion card.

  1. Back up any data on the hard drive.
  2. Make a copy of the drivers from the website onto a floppy disc, CD, DVD, or USB flash drive. The drivers that you download depends on the operating system that you want to install.
  3. Install the hard drive controller card onto your motherboard.
  4. Plug the hard drive into the controller card.
  5. Turn on your computer and open the operating system install wizard.
  6. Before you select the hard drive that you want to install the operating system onto, select the option to install third-party drivers.
  7. Point the driver installer to the floppy disc, CD, DVD, or USB flash drive.
  8. Install the drivers.
  9. Select the hard drive on the hard drive controller card as the location where you want to install the operating system.
  10. Complete the on-screen instructions to finish installing the operating system.

Before You Buy

Although you can adapt a Serial Attached SCSI (SAS) drive to connect to a standard SATA controller card, the card must support SAS commands in order to communicate with SAS drives. SAS drives have a different command set that is not present on SATA controllers.

This SATA controller card only supports standard SATA drives.

This device supports the ATA Packet Interface (ATAPI) protocol. ATAPI is required for optical drives, including CD-ROM drives, DVD-ROM drives, and Blu-ray players. Because this device supports ATAPI, optical drives are also supported.

 

Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.

Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.

The following are terms that are normally used in connection with RAID:

  • Striping: data is split between multiple disks.
  • Mirroring: data is mirrored between multiple disks.
  • Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.

Different RAID levels exist for different application requirements.

Refer to the following table for the list of RAID modes offered by some StarTech.com products:

RAID mode Description Operation Advantages Disadvantages Recovery
RAID 0 Striped disks Data is split evenly between two or more disks. Large size and the fastest speed. No redundancy. If one or more drives fails, this results in array failure.
RAID 1 Mirrored disks Two or more drives have identical data on them. A single drive failure will not result in data loss. Speed and size is limited by the slowest and smallest disk. Only one drive is needed for recovery.
RAID 3 Striped set with dedicated parity Data is split evenly between two or more disks, plus a dedicated drive for parity storage. High speeds for sequential read/write operations. Poor performance for multiple simultaneous instructions. A single drive failure will rebuild.
RAID 5 Striped disks with distributed parity Data is split evenly between three or more disks. Parity is split between disks. Large size, fast speed, and redundancy. The total array size is reduced by parity. A single drive failure will rebuild.
RAID 10 1+0; Striped set of Mirrored Subset Four or more drives are made into two mirrors that are striped. Larger size and higher speed than RAID-1, and more redundancy than RAID-0. No parity. Only one drive in a mirrored set can fail.
JBOD Just a Bunch Of Disks Any number of drives are accessed independently by the operating system. Software RAID modes can be used. Hardware RAID may have better performance. N/A
Big Spanning or Concatenation Data is written on one drive until it is full, and then the next drive(s) until it or they are full. Creates a very large and simple array.

No redundancy.

N/A
Clone RAID 1 + Spare

Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure.

Seamless operation when one drive fails in a RAID-1 array. Spare drive is not accessible to the user. Only one drive is needed for recovery.

 

Compliance and safety

Compliance letters

  • WEEE
    • Språk: English
  • RoHS
    • Språk: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen