Utgått

1000 Mbps Gigabit Ethernet PCI express Multiläges ST-fiberkort – 550 m

Anslut säkert en dator direkt till ett Gigabit ST-fibernätverk med multiläge genom en PCI express-kortplats

Produkt ID: PEX1000MMST

  • 1000 Mbps full duplex-användning
  • Gränssnitt för avancerad konfiguration för strömhantering (ACPI) 2.0
  • Verktyg för kabeldiagnostik

Den PEX1000MMST 1000 Mbps Gigabit fiberoptiska (MM ST) PCIe Ethernet-kortadaptern är den perfekta "fiber-till-skrivbordet"-lösningen.

Denna kortadapter för fiber Gigabit Ethernet är ett enkelt sätt att ansluta en dator direkt till ett fibernätverk med hög hastighet och kan installeras i datorn genom en PCI express-kortplats och lämpar sig perfekt för tillämpningar med hög bandbredd med stöd för full duplex och Gigabit-överföringshastigheter.

PEX1000MMST är idealisk för säkra nätverk och ger en direkt fiberanslutning som inte är känslig mot elektriska störningar som vanliga RJ45-nätverk är.

Täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Idealisk för säkra installationer - en direkt fiberanslutning innebär att man slipper elektriska störningar som kan vara ett problem med RJ45-nätverkskort
  • Perfekt för inbäddade och industriella fjärrsystem för övervakning och höghastighets videoövervakning
  • Behåll fulla Gigabit nätverkshastigheter till en fjärrterminal över stora avstånd

Fördelarna med StarTech.com

  • Direkt fiber innebär att man slipper elektriska störningar som kan påverka vanliga RJ45-nätverkskort
  • PCI express-gränssnittet ger äkta Gigabit nätverkshastigheter till skillnad från liknande PCI-fiberkort vars PCI-kortplats blir som en flaskhals
  • Enkel och snabb plug-and-play-installation

Partnernummer

  • UPC 065030841788

Kompatibilitet

  • Windows 8 logo
  • Windows Server 2012 logo
  • Mac OS X Mavericks (10.9) logo
  • Linux logo
  • Windows 7 logo
Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64)
Windows® Server 2012, 2008 R2
Mac OS® 10.x (Tested up to 10.9)
Linux

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Length 21,3 cm [8,4 in]
Package Width 50 mm [2,0 in]
Package Height 17,5 cm [6,9 in]
Fraktvikt (förpackning) 0 g [0,0 oz]
Hårdvara Portar 1
Gränssnitt RJ45 (Gigabit Ethernet)
Busstyp PCI Express
Korttyp Standardprofil
Industristandarder IEEE802.3z 1000Base-SX/1000Base-LX, IEEE802.3x, IEEE802.1Q, IEEE802.1p, IEEE802.3ad
Chipset-ID Realtek - RTL8168B
Indikatorer 1 - LED-indikatorer Aktivitet (gul)
Länk (grön)
Kontakt(er) 1 - Kontakttyp(er) PCI Express x1
1 - Externa portar Fiberoptisk ST duplex
Miljö Drifttemperatur 0°C to 45° C (32°F to 113°F)
Förvaringstemperatur -10°C to 70°C (14°F to 158°F)
Luftfuktighet 5 % - 95 % icke-kondenserande
Mjukvara OS-kompatibilitet Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64)
Windows® Server 2012, 2008 R2
Mac OS® 10.x (Tested up to 10.9)
Linux
Prestanda Maximal kabellängd 550 m [1804,0 ft]
Våglängd 850nm
Kompatibla nätverk 1000 Mbps (1 Gbps)
Ström Strömförbrukning 2.3W Max
Särskilda anmärkningar/krav Obs. Ej kompatibel med 10/100
Utseende Produktlängd 10,9 cm [4,3 in]
Produktbredd 83 mm [3,3 in]
Produkthöjd 20 mm [0,8 in]
Produktvikt 80 g [2,8 oz]
Vad det är i lådan 1 - Ingår i paketet PCI Express Gigabit Ethernet-adapter
CD med drivrutiner/bruksanvisning

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Drivrutin(er):

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Double-click Setup.exe.
  4. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  5. Your computer will automatically complete the driver installation and your device should be ready to use.

Problemsökning

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

Hur man

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Compliance and safety

Compliance letters

  • RoHS
    • Språk: English
  • WEEE
    • Språk: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen