Utgått

Gigabit Ethernet-fiber med öppen SFP PCI Express PCIe nätverkskortadapter NIC

Anslut en PCI express-baserad dator direkt till ett fiberoptiskt nätverk med ditt val av Gigabit SFP

Produkt ID: PEX1000SFP

  • Kompatibel med alla Gigabit SFP-moduler
  • Stöder auto-negotiation i full/halv duplex, Auto-MDI/MDIX
  • Kompatibelt med IEEE 802.3z 1000Base-SX/LX, IEEE802.1Q VLAN-taggning, IEEE802.1p Layer 2 Priority Encoding, IEEE 802.3x flödesreglering i full duplex, RFC 1157 SNMP v1

PEX1000SFP PCI express-nätverkskortet med öppen SFP för Gigabit Ethernet-fiber låter dig ansluta en PCI express-baserad dator direkt till ett fiberoptiskt nätverk med ditt val av Gigabit SFP.

PCIe SFP-nätverksadaptern är en mångsidig lösning för att ansluta datorn direkt till ett Gigabit fibernätverk och låter dig välja den Gigabit SFP som bäst passar din fibernätverksanslutning och dina avståndskrav (se våra för kompatibla lösningar).

Nätverkskortet med öppen SFP är idealisk för säkra nätverk och ger en direkt fiberanslutning som inte är känslig för elektroniska störningar som vanliga RJ45-nätverk är.

Täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Idealisk för säkra installationer - en direkt fiberanslutning innebär att man slipper elektriska störningar som kan vara ett problem med RJ45-nätverkskort
  • Perfekt för inbäddade och industriella fjärrsystem för övervakning och höghastighets videoövervakning
  • Behåll fulla Gigabit nätverkshastigheter till en fjärrterminal över stora avstånd

Fördelarna med StarTech.com

  • En öppen SFP-plats ger flexibiliteten att konfigurera SFP-nätverksadaptern så att den bäst passar dina nätverkskrav
  • En direkt fiber-till-skrivbordet-anslutning, idealisk för säkra nätverk

Partnernummer

  • UPC 065030848985

Kompatibilitet

  • Windows 8 logo
  • Windows Server 2012 logo
  • Linux logo
  • Windows 7 logo
Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), 2000
Windows Server® 2012, 2008 R2, 2003
Linux 2.4.x/ 2.6.x

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 50 mm [2,0 in]
Package Length 17,2 cm [6,8 in]
Package Width 21 cm [8,3 in]
Fraktvikt (förpackning) 214 g [7,6 oz]
Hårdvara Portar 1
Gränssnitt Fiber Ethernet
Busstyp PCI Express
Korttyp Standardprofil
Industristandarder IEEE 802.3z 1000Base-SX/LX, IEEE802.1Q VLAN-taggning, IEEE802.1p Layer 2 Priority Encoding, IEEE 802.3x flödesreglering i full duplex, RFC 1157 SNMP v1
Chipset-ID Realtek - RTL8168B
Marvell - 88E1111-RCJ1
Indikatorer 1 - LED-indikatorer Aktivitet (gul)
Länk (grön)
Kontakt(er) 1 - Kontakttyp(er) PCI Express x1
1 - Externa portar SFP-plats
Miljö Drifttemperatur 0°C to 45°C (32°F to 113°F)
Förvaringstemperatur -10°C to 70°C (14°F to 158°F)
Luftfuktighet 5~95 % RH (icke-kondenserande)
Mjukvara OS-kompatibilitet Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), 2000
Windows Server® 2012, 2008 R2, 2003
Linux 2.4.x/ 2.6.x
Prestanda Maximal dataöverföringshastighet 2000 Mbps (2 Gbps) - Full-duplex
Buffertstorlek 48 KB
Kompatibla nätverk 1000 Mbps (1 Gbps)
Auto MDIX Ja
Stöd för full-duplex Ja
Ström Strömförbrukning 2.3 W Max
Särskilda anmärkningar/krav Obs. Fiberdataöverföringshastigheter och avstånd beror på vilken SFP som används (säljes separat)
Utseende Produktlängd 85 mm [3,3 in]
Produktbredd 14 mm [0,6 in]
Produkthöjd 0 mm [0,0 in]
Produktvikt 68 g [2,4 oz]
Vad det är i lådan 1 - Ingår i paketet PCI Express-nätverkskort med öppen SFP
Drivrutin CD
Instruktionsbok

Tillbehör

Utgått
SFPG1340C

Cisco Compatible Gigabit Fiber SFP Transceiver Module SM LC w/ DDM – 40 km (Mini-GBIC)

Add, replace or upgrade SFP modules on Gigabit fiber equipment

Ditt pris
€154,99 EUR excl. VAT
€193,74 EUR incl. VAT
SFPG1320C

Cisco GLC-LH-SMD-kompatibel SFP-sändtagarmodul - 1000BASE-LH

1 000 Mbit/s (1 Gbit/s) | Fiber i enkelläge | LC | 20 km | Livstidsgaranti

Ditt pris
€76,99 EUR excl. VAT
€96,24 EUR incl. VAT
Utgått
SFPLHSM

Gigabit 1310nm Single Mode SFP Fiber Optical Transceiver - LC 40km

Add, replace or upgrade SFP modules on gigabit fiber equipment

Ditt pris
€121,99 EUR excl. VAT
€152,49 EUR incl. VAT
Utgått
SFPG1580C

Cisco Compatible Gigabit Fiber SFP Transceiver Module SM LC w/ DDM – 80 km (Mini-GBIC)

Add, replace or upgrade SFP modules on Gigabit fiber equipment

Ditt pris
€181,99 EUR excl. VAT
€227,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Drivrutin(er):

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Double-click Setup.exe.
  4. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  5. Your computer will automatically complete the driver installation and your device should be ready to use.

Problemsökning

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

Hur man

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

The drivers on our website include a Realtek Diagnostic Toolkit that you can use to easily set up a VLAN tag.

Make sure that you are logged in as the local administrator before continuing.

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Downloads). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. Once the download is complete, right-click the Realtek_PCI_GbE.zip file or the Realtek_PCIe_GbE.zip file.
  2. Select Extract All and note the location that the files will be extracted to.
  3. Select Extract. The extracted files will open automatically.
  4. In the list of extracted files, do one of the following:
  • If you are running Windows Vista/7/8, right-click the Setup.exe file and select Run as Administrator.
  • If you are running Windows XP, double-click the Setup.exe file.
  1. Follow the on-screen instructions to install the software.
  2. Open the software and under the VLAN settings, you can add, delete, or modify the VID (VLAN ID).

Compliance and safety

Compliance letters

  • RoHS
    • Språk: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen