Utgått

PCI Express Gigabit Ethernet NIC-nätverksadapterkort med 4 portar

Lägg till fyra Gigabit-nätverksgränssnitt till en stationär dator eller server med en ledig PCI Express x4-kortplats

Produkt ID: ST1000SPEX4

  • Fyra oberoende 10/100/1000 RJ45 Ethernet-portar
  • Stöd för jumboram
  • Helt kompatibelt med standarderna IEEE 802.3 IEEE 802.3u och IEEE 802.3ab

Detta fyra portars PCIe 10/100/1000 Mbps Gigabit Ethernet-adapterkort för nätverk har fyra Gigabit Ethernet-portar och är helt kompatibelt med IEEE standard 802.3/u/ab.

Gigabit Ethernet-adapterkortet för nätverk med hög kapacitet passar för alla PCI Express x4-klienter, servrar eller arbetsstationer och stödjer 4-kanalnätverk och maximala dataöverföringshastigheter på ut till 1000 Mbps i båda riktningarna (2000 Mbps totalt) – upp till tio gånger snabbare än 10/100-Ethernet.

Kompatibelt med ett brett sortiment av operativsystem, inklusive Windows 2000, XP, Vista, 7, Server 2003, Server 2008 R2, WinCE (4.2/5.0) och Linux (Redhat Enterprise, SCO, FreeBSD, etc…). Denna PCIe Gigabit NIC av hög kvalitet passar flera olika SMB:er och företagsapplikationer och täcks av StarTech.coms 2-årsgaranti för hårdvaror och gratis livstidsgaranti på teknisk support.

Användning

  • Perfekt för VM-miljöer med flera verksamheter som kräver delade eller dedicerade NIC:er
  • Särskilt framtaget för stationära PC-klienter och servrar med begränsat antal kortplatser och arbetsstationer med en PCI Express-kortplats.
  • Tillhandahåller redundant anslutningsbarhet för att säkerställa oavbruten nätverksanslutning

Fördelarna med StarTech.com

  • Tillhandahåller fyra oberoende Gigabit Ethernet-portar men tar bara upp en utbyggnadskortplats
  • Stöd för IEEE standard 802.1Q gör att varje enskild port kan drivas i ett separat virtuellt LAN (VLAN)
  • Avstängning och strömsparläge för nedlänkning sparar ström när portarna inte används

Partnernummer

  • UPC 065030839457

Kompatibilitet

  • Windows 8 logo
  • Windows Server 2012 logo
  • Mac OS X Mavericks (10.9) logo
  • Linux logo
  • Windows 7 logo
Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), CE 5.0/4.2, 2000, ME, 98SE
Windows Server® 2012, 2008 R2, 2003(32/64)
Mac OS® 10.4 and up (Intel-based - Tested up to 10.9)
Linux Kernel 2.4.x and up
SCO OpenServer 5.0.7/ 6

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Length 23 cm [9,1 in]
Package Width 44 mm [1,7 in]
Package Height 16,3 cm [6,4 in]
Fraktvikt (förpackning) 240 g [8,5 oz]
Hårdvara Portar 4
Gränssnitt RJ45 (Gigabit Ethernet)
Busstyp PCI Express
Korttyp Standardprofil
Industristandarder Kompatibel med standarderna IEEE 802.3 IEEE 802.3u, IEEE 802.3ab
Chipset-ID Realtek - RTL8111C
Indikatorer 4 - LED-indikatorer Gul – aktivitets-LED
Grön – länk-LED
Kontakt(er) 1 - Kontakttyp(er) PCI Express x4
4 - Externa portar RJ-45
Miljö Drifttemperatur 0°C to 55°C (32°F to 131°F)
Förvaringstemperatur -20°C to 85°C (-4°F to 185°F)
Luftfuktighet 5~95 % RH
Mjukvara OS-kompatibilitet Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), CE 5.0/4.2, 2000, ME, 98SE
Windows Server® 2012, 2008 R2, 2003(32/64)
Mac OS® 10.4 and up (Intel-based - Tested up to 10.9)
Linux Kernel 2.4.x and up
SCO OpenServer 5.0.7/ 6
Prestanda Maximal dataöverföringshastighet 1000 Mbps
Buffertstorlek 48 KB
Kompatibla nätverk 10/100/1000 Mbps
Auto MDIX Ja
Stöd för full-duplex Ja
Medeltid mellan fel (MTBF) 117,500 Hours
Utseende Produktlängd 14 cm [5,5 in]
Produktbredd 10,2 cm [4,0 in]
Produkthöjd 18 mm [0,7 in]
Produktvikt 250 g [8,8 oz]
Vad det är i lådan 1 - Ingår i paketet PCI Express-nätverkskort med 4 portar
Drivrutin CD
Instruktionsbok

Tillbehör

Ditt pris
€5,99 EUR excl. VAT
€7,49 EUR incl. VAT
Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
M45PATCH6BL

6 ft Cat5e Blue Molded RJ45 UTP Cat 5e Patch Cable - 6ft Patch Cord

Skapa snabba Ethernet nätverksanslutningar med denna högkvalitativa Cat5e-kabel med ström-över-Ethernet

Ditt pris
€1,99 EUR excl. VAT
€2,49 EUR incl. VAT
M45PATCH10BL

Cat5e Patch Cable with Molded RJ45 Connectors - 10 ft. - Blue

Skapa snabba Ethernet nätverksanslutningar med denna högkvalitativa Cat5e-kabel med ström-över-Ethernet

Ditt pris
€2,99 EUR excl. VAT
€3,74 EUR incl. VAT
M45PATCH10BK

Cat5e patchkabel med gjutna RJ45-kontakter - 3 m - svart

Skapa snabba Ethernet nätverksanslutningar med denna högkvalitativa Cat5e-kabel med ström-över-Ethernet

Ditt pris
€2,99 EUR excl. VAT
€3,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Drivrutin(er):

Inbyggd programvara

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Double-click Setup.exe.
  4. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  5. Your computer will automatically complete the driver installation and your device should be ready to use.

Problemsökning

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

Du bör inte uppgradera enhetens inbyggda programvara om du inte har några problem med enhetens funktioner. Du behöver bara uppgradera om du har problem med enheten och är säker på att problemet är den inbyggda programvaran.  Du kan bekräfta detta genom att läsa igenom den medföljande dokumentationen eller kontakta vår tekniska avdelning. Felaktig uppgradering av inbyggd programvara kan resultera i minskade prestanda så vi rekommenderar att du kontaktar StarTech.com först.

Hur man

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

The drivers on our website include a Realtek Diagnostic Toolkit that you can use to easily set up a VLAN tag.

Make sure that you are logged in as the local administrator before continuing.

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Downloads). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. Once the download is complete, right-click the Realtek_PCI_GbE.zip file or the Realtek_PCIe_GbE.zip file.
  2. Select Extract All and note the location that the files will be extracted to.
  3. Select Extract. The extracted files will open automatically.
  4. In the list of extracted files, do one of the following:
  • If you are running Windows Vista/7/8, right-click the Setup.exe file and select Run as Administrator.
  • If you are running Windows XP, double-click the Setup.exe file.
  1. Follow the on-screen instructions to install the software.
  2. Open the software and under the VLAN settings, you can add, delete, or modify the VID (VLAN ID).

Compliance and safety

Compliance letters

  • RoHS
    • Språk: English
  • WEEE
    • Språk: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen