Utgått

Dual Port Gigabit PCI Express Server Network Adapter Card - PCIe NIC

Add dual Gigabit Ethernet ports to a client, server or workstation through a PCI Express slot

Produkt ID: ST1000SPEXD3

  • Two 10/100/1000Mbps compatible RJ-45 Ethernet ports
  • Jumbo Frame support up to 9k bytes
  • Compatible with PCI Express Base Specification 2.0 (backward compatible with 1.0a/1.1)

The ST1000SPEXD3 PCI Express Dual Port Gigabit Server Network Adapter Card (PCIe NIC) lets you add two gigabit Ethernet ports to a client, server or workstation through a single PCI Express slot. Each port provides 10/100/1000 Mbps capable Ethernet and is fully compatible with IEEE 802.3/u/ab standards.

Suitable for any standard PCI Express-enabled system, the 2-port Ethernet card supports full-duplex flow control for maximum data transfer speeds of up to 2000 Mbps - an ideal single card, dual NIC solution for setting up dual-homed, or multi-homed host configurations providing added security to corporate networks.

The dual port server adapter is compliant with the PCIe 2.0 standard and features support for Jumbo Frames and 802.1q VLAN tagging as well as Wake on LAN (WOL). The adapter includes an optional low profile bracket that can be used for installation into a standard or low profile computer chassis.

Backed by a StarTech.com 2-year warranty and free lifetime technical support.

Användning

  • Ideal for VM environments with multiple operating systems, requiring shared or dedicated NICs
  • Provide redundant connectivity to ensure an uninterrupted network connection
  • Configure a dual-homed proxy or gateway system for an added layer of security
  • Specially designed for desktop PC clients, servers, and workstations with few PCI Express slots available

Fördelarna med StarTech.com

  • Protect critical networked systems with a redundant and independent Gigabit port
  • Optimize network traffic with support for advanced features such as Jumbo Frames and VLAN tagging
  • Maximize your virtualized server’s networking efficiency with dedicated ports

Partnernummer

  • UPC 065030850865

Kompatibilitet

  • Windows 8 logo
  • Windows Server 2012 logo
  • Mac OS X Mavericks (10.9) logo
  • Linux logo
  • Windows 10 logo
  • Windows 7 logo
  • Mac OS X Yosemite (10.10) logo
Windows® 10 (32/64), 8 / 8.1 (32/64), 7 (32/64), Vista (32/64), XP (32/64), 2000
Windows Server® 2012, 2008 R2, 2003
Mac OS 10.4 to 10.10
Linux

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 40 mm [1,6 in]
Package Length 22,5 cm [8,9 in]
Package Width 16 cm [6,3 in]
Fraktvikt (förpackning) 190 g [6,7 oz]
Hårdvara Portar 2
Gränssnitt RJ45 (Gigabit Ethernet)
Busstyp PCI Express
Korttyp Standardprofil (inkl. LP-fäste)
Porttyp Inbyggd på kort
Industristandarder PCI Express Base Specification 2.0
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Chipset-ID Realtek - RTL8111E
PLX - PEX8608
Indikatorer 2 - LED-indikatorer Green - Link/Activity
Yellow - Gigabit Mode
Kontakt(er) 1 - Kontakttyp(er) PCI Express x1
2 - Externa portar RJ-45
Miljö Drifttemperatur 0°C to 55°C (32°F to 131°F)
Förvaringstemperatur -20°C to 85°C (-4°F to 185°F)
Luftfuktighet 5~95% RH
Mjukvara OS-kompatibilitet Windows® 10 (32/64), 8 / 8.1 (32/64), 7 (32/64), Vista (32/64), XP (32/64), 2000
Windows Server® 2012, 2008 R2, 2003
Mac OS 10.4 to 10.10
Linux
Prestanda Maximal dataöverföringshastighet 2000 Mbps (full-duplex), 1000 Mbps (half-duplex)
Buffertstorlek 48 KB
Kompatibla nätverk 10/100/1000 Mbps
Auto MDIX Ja
Stöd för full-duplex Ja
Jumbo Frame Support 9K max.
Stödda protokoll IEEE 802.1Q VLAN tagging, IEEE 802.1P Layer 2 Priority Encoding and IEEE 802.3x Full Duplex Flow Control
Särskilda anmärkningar/krav System- och kabelkrav Available PCI Express slot
Utseende Produktlängd 92 mm [3,6 in]
Produktbredd 16 mm [0,6 in]
Produkthöjd 68 mm [2,7 in]
Produktvikt 54 g [1,9 oz]
Vad det är i lådan 1 - Ingår i paketet PCIe Network Card
Low Profile Bracket
Driver CD
Instruction Manual

Tillbehör

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
M45PATCH10BL

Cat5e Patch Cable with Molded RJ45 Connectors - 10 ft. - Blue

Skapa snabba Ethernet nätverksanslutningar med denna högkvalitativa Cat5e-kabel med ström-över-Ethernet

Ditt pris
€2,99 EUR excl. VAT
€3,74 EUR incl. VAT
M45PATCH10BK

Cat5e patchkabel med gjutna RJ45-kontakter - 3 m - svart

Skapa snabba Ethernet nätverksanslutningar med denna högkvalitativa Cat5e-kabel med ström-över-Ethernet

Ditt pris
€2,99 EUR excl. VAT
€3,74 EUR incl. VAT
M45PATCH6BL

6 ft Cat5e Blue Molded RJ45 UTP Cat 5e Patch Cable - 6ft Patch Cord

Skapa snabba Ethernet nätverksanslutningar med denna högkvalitativa Cat5e-kabel med ström-över-Ethernet

Ditt pris
€1,99 EUR excl. VAT
€2,49 EUR incl. VAT
Ditt pris
€5,99 EUR excl. VAT
€7,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Drivrutin(er):

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Right-click Setup.exe. 
  4. Click Run as Administrator.

Note: If the Run as Administrator option is not available, you might be attempting to run the installer from within the zipped file. Extract the files using the instructions in Step 2.

  1. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  2. Your computer will automatically complete the driver installation and your device should be ready to use.

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Double-click Setup.exe.
  4. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  5. Your computer will automatically complete the driver installation and your device should be ready to use.

Problemsökning

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

Hur man

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

Virtual local area network (VLAN) tagging requires that the network interface card (NIC) and the router or switch that you use support protocol IEEE 802.1q.

Depending on the NIC, you can set your VLAN ID in Device Manager.  Not all NICs that support VLAN tagging have this option.

Setting your VLAN ID in Device Manager

Note: Log in as the local administrator before continuing.

To open Device Manager:

  • Press Windows key + R
  • Type devmgmt.msc
  • Click OK.
  1. In Device Manager, open Network adapters.
  2. Right-click on the NIC and choose Properties.
  3. Click the Advanced tab.
  4. Scroll down to VLAN ID.
  5. Set the ID that you would like the NIC to have and click OK.

Setting up your VLAN Tagging and Setting a VLAN ID

How you perform this task depends on your router or switch.  Consult the manual or manufacturer of your router or switch for more details.

In your router or switch, you can VLAN tag a device by the VLAN ID if you set one previously, or by the MAC address of the computer.  Your router or switch will list all IP devices by MAC address.

The drivers on our website include a Realtek Diagnostic Toolkit that you can use to easily set up a VLAN tag.

Make sure that you are logged in as the local administrator before continuing.

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Downloads). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. Once the download is complete, right-click the Realtek_PCI_GbE.zip file or the Realtek_PCIe_GbE.zip file.
  2. Select Extract All and note the location that the files will be extracted to.
  3. Select Extract. The extracted files will open automatically.
  4. In the list of extracted files, do one of the following:
  • If you are running Windows Vista/7/8, right-click the Setup.exe file and select Run as Administrator.
  • If you are running Windows XP, double-click the Setup.exe file.
  1. Follow the on-screen instructions to install the software.
  2. Open the software and under the VLAN settings, you can add, delete, or modify the VID (VLAN ID).

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your expansion card, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your expansion card is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Compliance and safety

Compliance letters

  • WEEE
    • Språk: English
  • RoHS
    • Språk: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen