Produkt ID: US1GC301AU2R
Nu kan du lägga till trådad nätverksåtkomst genom USB-C™- eller Thunderbolt™ 3-porten på din bärbara eller stationära dator och enkelt ansluta till dina USB 3.0-enheter (Type A). Denna Gigabit Ethernet-nätverksadapter ger dig åtkomst till två tillförlitliga GbE-portar utan att behöva installera drivrutiner. Det är det perfekta tillbehöret för din MacBook, ChromeBook Pixel™, Dell™ XPS™ 12, Dell Latitude™ 12 7000-serien 2-i-1 eller annan enhet som har en USB Type-C™-port.
Nätverksadaptern utnyttjar hastigheten på 5 Gbps hos USB 3.0 (även känd som USB 3.1 Gen 1) för att ge full bandbredd till din Gigabit-nätverksanslutning utan flaskhalsar. Detta besparar dig tid genom att göra det enklare att få åtkomst till väldigt stora filer över ditt nätverk med Gigabit-hastighet.
För extra mångsidighet stöder nätverksadaptern många olika praktiska funktioner, som till exempel Wake-On-LAN, VLAN-taggning, korsad detektering och autokorrigering (Auto MDIX), kontrollsumma (IPv4, IPv6, TCP, UDP) och avlastning för stor överföring.
Vissa datorer med USB Type-C har endast en USB-C-port för extern anslutning, som inte går att ansluta med dina befintliga USB Type-A-enheter. Denna Gigabit-adapter har en inbyggd USB 3.0 Type-A-port, så medan adaptern är ansluten till datorn för att ge nätverksåtkomst kan du även ansluta till USB-tillägg som behöver en USB Type-A-kontakt. Nätverksadaptern är även bakåtkompatibel med USB 2.0-system.
Kom igång snabbt. Nätverksadaptern har inbyggt stöd för drivrutiner för att garantera en snabb setup. Koppla helt enkelt in adaptern i USB Type-C-porten på din bärbara dator och anslut till ditt nätverk. Nätverksadapterns chipset ger inbyggt stöd för drivrutiner i Chrome OS™ och Windows® 8.1 och stöder Mac OSX (10.10) med installation av drivrutiner.
USB Type-C-kontakten är mindre och enklare att använda än tidigare USB-kontakter. Det är en vändbar kontakt som kan anslutas till dina enheter med båda sidor upp. Du kan koppla in kabeln rätt varje gång - utan frustration eller risk för skador på porten.
US1GC301AU2R täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Package Height | 30 mm [1,2 in] |
Package Length | 14,4 cm [5,7 in] | |
Fraktvikt (förpackning) | 112 g [4,0 oz] | |
Package Width | 17,2 cm [6,8 in] | |
Hårdvara | Portar | 2 |
Gränssnitt | RJ45 (Gigabit Ethernet) | |
Busstyp | USB 3.0 | |
USB-passthrough | Ja | |
Industristandarder | IEEE 802.3, 802.3u och 802.3ab | |
Chipset-ID | VIA/VLI - VL812 ASIX - AX88179 |
|
Indikatorer | 4 - LED-indikatorer | 2x Gigabit länk/aktivitet2x 10/100 länk/aktivitet |
Kontakt(er) | 1 - Kontakttyp(er) | USB 3.0 A (Snabbladdning, 9-stifts) |
USB Type-C (24-stifts) USB 3.0 (5Gbps) | ||
2 - Externa portar | RJ-45 | |
Miljö | Drifttemperatur | 5°C to 50°C (41°F to 122°F) |
Förvaringstemperatur | -20°C to 60°C (-4°F to 140°F) | |
Luftfuktighet | 20%~80% | |
Mjukvara | OS-kompatibilitet | Windows® XP, Vista, 7, 8, 8.1, 10 Windows Server® 2003, 2008 R2, 2012, 2016, 2019 Mac OS® 10.6 till 10.15 VLAN-taggning stöds för närvarande inte i Mac OS Linux Kernel 2.6.25 till 4.11.x Endast LTS-versioner |
Prestanda | Maximal dataöverföringshastighet | 5 Gbps (USB 3.0) 2 Gbps (Ethernet - full-duplex) |
Maximal kabellängd | 100 mm [3,9 in] | |
Bandbredd | 5 Gbps (USB 3.0) 2 Gbps (Ethernet - Full-Duplex) |
|
Typ och hastighet | USB 3.0 - 5 Gbit/s | |
Kompatibla nätverk | 10/100/1000 Mbps | |
Auto MDIX | Ja | |
Stöd för full-duplex | Ja | |
Jumbo Frame Support | 4K max. | |
Ström | Power Source | Strömförsörjd via USB |
Särskilda anmärkningar/krav | System- och kabelkrav | Ledig USB Type-C-port |
Utseende | Form Factor | Inbyggd kabel |
Produktvikt | 54 g [1,9 oz] | |
Färg | Svart | |
Kabinettyp | Av plast | |
Produktlängd | 75 mm [3,0 in] | |
Produktbredd | 60 mm [2,4 in] | |
Produkthöjd | 16 mm [0,6 in] | |
Vad det är i lådan | 1 - Ingår i paketet | USB-C till dubbel Gigabit Ethernet-adapter |
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test your cables, it is recommended that you do the following:
When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:
Sometimes an on-board network interface card (NIC) conflicts with a new NIC. In these cases it is best to disable the on-board NIC.
The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible. To do this, consult your motherboard manual.
You can also disable any NIC in Windows. Here is how you do this:
First click Start, or, in Windows 10 and 8, hold down the Windows key and press X. Then click Control Panel.
Windows 10
Windows 8
Windows 7
Windows Vista
Windows XP
If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings. You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.
Note: You must log in as the local administrator before you continue.
To open Device Manager:
If the USB device does not work after your computer has been in extended hibernation, it is likely that Windows has automatically turned off the USB Root hub to save power.
The steps below outline how to configure the USB root hub to stay on during hibernation, to prevent this from happening.
Windows 10 / 8
Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.
Windows 7 / Vista
Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.
Windows XP
Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.
StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:
Virtual local area network (VLAN) tagging requires that the network interface card (NIC) and the router or switch that you use support protocol IEEE 802.1q.
Depending on the NIC, you can set your VLAN ID in Device Manager. Not all NICs that support VLAN tagging have this option.
Setting your VLAN ID in Device Manager
Note: Log in as the local administrator before continuing.
To open Device Manager:
Setting up your VLAN Tagging and Setting a VLAN ID
How you perform this task depends on your router or switch. Consult the manual or manufacturer of your router or switch for more details.
In your router or switch, you can VLAN tag a device by the VLAN ID if you set one previously, or by the MAC address of the computer. Your router or switch will list all IP devices by MAC address.
For most operating systems, network interface card (NIC) teaming requires that the NIC and the router or switch support the protocol IEEE 802.1ax or IEEE 802.3ad.
Windows Server 2012, however, has native support for NIC teaming, so the NIC and the router or switch do not need to support the protocols. To configure NIC teaming in Windows Server 2012 do the following:
If you view the Networking Connections section in the window, you can see the NIC team in the list as well as the Ethernet and wireless adapter cards.
USB-C is a type of USB connector that is capable of supporting the following:
If using Thunderbolt 3 over USB-C, the connection is capable of additional features. For example, Thunderbolt 3 is capable of 40Gbps of total bandwidth. For more information, refer to the following FAQ: https://www.startech.com/faq/thunderbolt-3-port-capabilities.
Not all USB-C ports or devices are capable of supporting all of the features listed above, or all of the features at the maximum capabilities. If you require a specific USB-C feature, your USB host connection, cables, and device must all support the feature that you require. For more information about whether your components support specific USB-C features, refer to the information provided by the manufacturers.