USB 3.0 till Gigabit-nätverksadapter med inbyggd USB-hubb med 2 portar

Lägg till Gigabit Ethernet-anslutning och två USB 3.0-portar till din bärbara dator eller surfplatta genom en enda USB-port

Produkt ID: USB31000S2H

  • Ge din bärbara dator eller surfplatta stöd för full Gigabit-bandbredd genom en USB 3.0-värdanslutning
  • Anslut extra tillägg med två USB 3.0-portar
  • Inbyggt stöd för drivrutiner (Windows, Mac och Chrome OS)
Ditt pris
€52,99 EUR excl. VAT
€66,24 EUR incl. VAT

Lägg till kraftfull nätverksåtkomst till din surfplatta, Ultrabook™ eller bärbara dator även om den inte har en inbyggd RJ45-port. Denna USB 3.0 till Gigabit-nätverksadapter ger dig trådad nätverksåtkomst - och ger dig två USB 3.0-genomströmningsportar som låter dig ansluta extra USB-enheter.

Kraftfulla Gigabit-nätverksanslutningar

USB 3.0-nätverksadaptern är idealisk för kontoret eller hemmet och stöder full Gigabit-bandbredd genom att utnyttja prestandan från USB 3.0 (5 Gbps). Du får snabb åtkomst till väldigt stora filer över ett Gigabit-nätverk och sparar värdefull tid varje dag.

Inbyggt stöd för drivrutiner gör installationen enkel

Kom igång snabbt. Koppla helt enkelt in Ethernet-kabeladaptern i USB-porten på din bärbara dator och anslut till ditt nätverk. Nätverksadapterns chipset ger inbyggt stöd för drivrutiner så att du slipper installera extra mjukvara.

Anslut dina USB-enheter till extraportarna

Ge din bärbara dator eller surfplatta fler möjligheter genom att ansluta USB-enheter som till exempel skrivare och externa kabinett för solid state-enheter eller hårddiskar med hjälp av de två USB 3.0-portarna. Du kan dessutom ansluta musen, tangentbordet, USB-minnet eller andra USB-enheter som inte drar så mycket ström, utan att extra ström behövs.

Kompakt och lätt för perfekt bärbarhet

Denna USB Gigabit-nätverksadapter är kompakt och bärbar och är den idealiska nätverksadaptern för stationära datorer eller tillbehör för bärbara datorer. Du behöver inte ta med dig en strömadapter för att använda den eftersom den strömförses direkt från USB-värdporten.

USB31000S2H täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Idealisk för en Ultrabook, surfplatta eller tunn bärbar dator som inte har en RJ45-port
  • Den idealiska ersättaren för en äldre LAN-port
  • Anslut tillägg om skrivare eller externa SSD/HDD-kabinett till den inbyggda USB-hubben med två portar
  • Ta med dig adaptern tillsammans med den bärbara datorn som ett bärbart USB-drivet tillbehör

Partnernummer

  • Ingram Micro Sweden V933535
  • UPC 065030862400

Kompatibilitet

  • Mac OS X El Capitan (10.11) logo
  • Chrome OS logo
  • Windows 8 logo
  • Windows 7 logo
  • Linux logo
  • Windows Server 2012 logo
  • Windows 10 logo
  • macOS Sierra (10.12) logo
  • Windows Server 2016 logo
  • macOS Mojave (10.14) logo
  • Windows Server 2019 logo
  • macOS High Sierra (10.13) logo
  • macOS Catalina (10.15) logo
  • macOS Big Sur (11.0) logo
Windows® XP, Vista, 7, 8, 8.1, 10
Windows Server® 2003, 2008 R2, 2012, 2016, 2019
Mac OS X® 10.7 till 10.15 VLAN-taggning stöds för närvarande inte i Mac OS
Linux Kernel 2.6.25 till 4.11.x Endast LTS-versioner Chrome OS®️

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Fraktvikt (förpackning) 106 g [3,7 oz]
Package Length 14,2 cm [5,6 in]
Package Width 17 cm [6,7 in]
Package Height 30 mm [1,2 in]
Hårdvara Portar 1
Gränssnitt USB 3.0
Busstyp USB 3.0
USB-passthrough Ja
Industristandarder IEEE 802.3 10BASE-T, IEEE 802.3ab 1000BASE-T, IEEE 802.3u 100BASE-TX och IEEE 802.3X full-duplex
Chipset-ID Realtek - RTL8153
Kontakt(er) 1 - Kontakttyp(er) USB Type-A (9-stifts) USB 3.0 (5 Gbps)
RJ-45
2 - Kontakttyp(er) USB Type-A (9-stifts) USB 3.0 (5 Gbps)
Miljö Drifttemperatur 0°C to 70°C (32°F to 158°F)
Förvaringstemperatur -10°C to 55°C (14°F to 131°F)
Luftfuktighet Luftfuktighet vid förvaring: 5 % ~ 90 % RH (ingen kondensering) Luftfuktighet vid drift: 50 % ~ 80 % RH
Mjukvara OS-kompatibilitet Windows® XP, Vista, 7, 8, 8.1, 10
Windows Server® 2003, 2008 R2, 2012, 2016, 2019
Mac OS X® 10.7 till 10.15 VLAN-taggning stöds för närvarande inte i Mac OS
Linux Kernel 2.6.25 till 4.11.x Endast LTS-versioner Chrome OS®️
Prestanda Maximal dataöverföringshastighet 5 Gbps - USB 3.0/2 Gbps - Full-duplex Gigabit Ethernet
Typ och hastighet USB 3.0 - 5 Gbit/s
Överspänningsskydd 5 kV
Kompatibla nätverk 10/100/1000 Mbps
Auto MDIX Ja
Stöd för full-duplex Ja
Jumbo Frame Support 9K max.
Allmänna specifikationer Max Power Draw: 150mA
Medeltid mellan fel (MTBF) 637,901 timmar
Ström Strömförbrukning Max 1092mA
Utseende Form Factor Inbyggd kabel
Produktvikt 0 g [0,0 oz]
Färg Svart
Kabinettyp Av plast
Produktlängd 25,5 cm [10,0 in]
Produktbredd 37 mm [1,5 in]
Produkthöjd 17 mm [0,7 in]
Vad det är i lådan 1 - Ingår i paketet USB 3.0 till Gigabit-nätverksadapter
Instruktionsbok

Tillbehör

USB3SAUB3

3 ft SuperSpeed USB 3.0 Cable A to Micro B

Connect a USB 3.0 Micro USB External Hard drive to your PC or laptop

Ditt pris
€9,99 EUR excl. VAT
€12,49 EUR incl. VAT
ECUSB3S22

2 Port ExpressCard SuperSpeed USB 3.0 Card Adapter with UASP Support

Add 2 USB 3.0 Ports to a Laptop through an ExpressCard Slot

Ditt pris
€39,99 EUR excl. VAT
€49,99 EUR incl. VAT
Utgått
PEXUSB3S400

PCI Express PCIe SuperSpeed USB 3.0-kontrollerkortadapter med 4 oberoende portar och UASP - SATA-ström

Lägg till 4 oberoende SuperSpeed USB 3.0-portar till datorn genom en PCI express-kortplats

Ditt pris
€138,99 EUR excl. VAT
€173,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Drivrutin(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Right-click Setup.exe. 
  4. Click Run as Administrator.

Note: If the Run as Administrator option is not available, you might be attempting to run the installer from within the zipped file. Extract the files using the instructions in Step 2.

  1. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  2. Your computer will automatically complete the driver installation and your device should be ready to use.

Problemsökning

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

If the USB device does not work after your computer has been in extended hibernation, it is likely that Windows has automatically turned off the USB Root hub to save power. 

The steps below outline how to configure the USB root hub to stay on during hibernation, to prevent this from happening.
 

Windows 10 / 8

  1. On your keyboard, press the Windows key + X and select Control Panel.
  2. Click Hardware and Sound, then click Power Options.
  3. Click Change plan settings for the plan you want to change.
  4. Click Change advanced power settings.
  5. Click the plus sign (+) next to “USB settings” and “USB selective suspend setting” to expand the options and change the setting to Disabled.
  6. Click OK to apply the setting.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

Windows 7 / Vista

  1. Click the Start button and select Control Panel.
  2. Click Hardware and Sound, then click Power Options.
  3. Click Change plan settings for the plan you want to change.
  4. Click Change advanced power settings.
  5. Click the plus sign (+) next to “USB settings” and “USB selective suspend setting” to expand the options and change the setting to Disabled.
  6. Click OK to apply the setting.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

Windows XP

  1. On your desktop, right-click the My Computer icon and select Properties.
  2. Click the Device Manager tab.
  3. Expand Universal Serial Bus controllers by clicking the arrow to the left of it.
  4. Right-click the first USB Root Hub device and select Properties.
  5. Click the Power Management tab.
  6. Clear the box next to Allow the computer to turn off this device to save power.
  7. Click OK to apply the setting.
  8. Repeat steps 4-7 for any remaining devices in the Universal Serial Bus Controllers section with “Root Hub” in the name.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

Hur man

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

To confirm that Windows detects your USB device, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Compliance and safety

Compliance letters

  • RoHS
    • Språk: English
  • WEEE
    • Språk: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen