Produkt ID: SATSASDUPE11
Denna fristående hårddiskduplikator och -raderare stöder både SATA- och SAS-hårddiskar och passar jättebra för företagslagring och datacenter-applikationer. Kompatibel med formfaktorerna 2,5" och 3,5" och är en mångsidig och kostnadseffektiv lösning för hårddiskhantering.
Med hårddiskduplikatorn kan du klona SATA- eller SAS-hårddiskar 1:1 med hastigheter på upp till 13 GB/minut. Den är ett kraftfullt verktyg för IT-proffs och IT-administratörer för att effektivt hantera hårddiskar för serverdelsinfrastruktur eller hårddiskar som distribuerats till organisationsmedarbetare. Den bidrar till ett effektivare arbetsflöde genom att möjliggöra duplicering utan att en dator eller ett program används. Du kan snabbt säkerhetskopiera och arkivera data, duplicera data för avbildning av hårddisk eller föra över innehåll till extra hårddiskar för kontorsarbetare, vårdpersonal, myndighetspersonal eller andra medarbetare.
Hårddiskklonaren/raderaren har fyra dupliceringslägen inklusive system och fil, alla partitioner, sektor-för-sektor (hela hårddisken) och procentkopiering.
Radera enkelt SATA- eller SAS-hårddiskar utan en värddator. Som en hårddiskraderare kan SATSASDUPE11 radera två hårddiskar samtidigt och har sex olika raderingslägen inklusive snabbradering, NIST 800-88 Rev. 1 Rensa kompatibel Säker radering, 1-pass-överskrivning, 3-pass-överskrivning (DoD), 3-pass-radering och jämför samt 7-pass-överskrivning.
De olika raderingslägena garanterar att data säkert kan raderas när du återanvänder hårddiskar. Detta lättar på integritet-relaterade problem vid radering av känslig data vilket är viktigt för många professionella kontor som till exempel medicinska, juridiska och revisorsfirmor.
Med hårddiskraderaren får du dessutom en förteckning över slutförda raderingsjobb med inbyggd loggning av radering för deklarationsskäl. Den ansluts till en seriell RS232-skrivare för att skriva ut en rapport över raderingsproceduren och bekräfta att raderingen har lyckats. Kvittot visar tydligt tid och datum för raderingen samt vilket raderingsläge som använts.
Hårddiskduplikatorn och -raderaren ger IT-proffs en lättanvänd lösning i en kontors- eller servermiljö. Den har enkla knappar för menynavigering och en inbyggd LCD-display som tydligt identifierar duplicerings- eller raderingsläget och status. Eftersom den är OS-oberoende behövs inga program eller drivrutiner.
Dess fristående användning ger snabb setup utan att behöva använda en dator. Du kan enkelt flytta enheten från rum till rum för att arbeta med hårddiskart på olika platser.
SATSASDUPE11 täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Package Height | 91 mm [3,6 in] |
Package Length | 38,2 cm [15,0 in] | |
Fraktvikt (förpackning) | 2,4 kg [5,3 lb] | |
Package Width | 19,2 cm [7,6 in] | |
Hårdvara | Antal enheter | 2 |
Enhetsstorlek | 2.5in & 3.5in | |
Enhetstyp | SAS & SATA | |
Fläkt(ar) | Nej | |
Chipset-ID | Xilinx - SPARTAN-6 | |
Indikatorer | 2 - LED-indikatorer | Ström |
Godkänd | ||
Underkänd | ||
Kontakt(er) | 2 - Enhetskontakter | SFF-8482 (29-stifts, data & ström, intern SAS) |
1 - Övriga gränssnitt | DB 9-pin Serial | |
USB Type-A (9-stifts) USB 3.0 (5 Gbps) | ||
Miljö | Drifttemperatur | 5°C to 45°C (41°F to 113°F) |
Förvaringstemperatur | -20°C to 85°C (-4°F to 185°F) | |
Luftfuktighet | 20% ~ 80% | |
Prestanda | 4Kn Support | Ja |
Port Multiplier | Nej | |
Duplication Modes | System and File | |
Duplication Speed | 13GBpm | |
Raderingslägen | Quick Erase | |
Secure Erase (NIST SP 800-88 Rev 1 - Purge) | ||
Duplication Modes | All Partitions | |
Raderingslägen | 1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear) | |
3-Pass Erase and Compare | ||
Duplication Modes | Sector by Sector (Whole Drive) | |
Raderingslägen | 3-Pass Overwrite | |
Duplication Modes | Percentage Copy | |
Raderingslägen | 7-Pass Overwrite | |
Ström | Power Source | AC-adapter medföljer |
Inspänning | 100 - 240 AC | |
Inström | 1.2A | |
Utspänning | 12V DC | |
Utström | 7A | |
Polaritet på mittpol | Positiv | |
Kontakttyp | N | |
Strömförbrukning | 90 | |
Särskilda anmärkningar/krav | Obs. | Receipt printing through the RS232 serial port requires a printer which supports the ESC/P printer control language. |
Utseende | Färg | Svart |
Kabinettyp | Stål | |
Produktlängd | 19,4 cm [7,6 in] | |
Produktbredd | 90 mm [3,5 in] | |
Produkthöjd | 35 mm [1,4 in] | |
Produktvikt | 695 g [24,5 oz] | |
Vad det är i lådan | 1 - Ingår i paketet | SATA/SAS-duplikator och raderare |
universell strömadapter (NA/JP, UK, EU, AU) | ||
2 - Ingår i paketet | anslutningskablar för hårddisk | |
hårddiskkuddar | ||
1 - Ingår i paketet | snabbstartsguide |
Provides safe handling and anti-static protection for most 2.5in hard drives
Provides safe handling and anti-static protection for most 2.5in hard drives
Provide protection against shocks/impacts to a 2.5in hard drive
Konvertera en mSATA mini-SSD till en vanlig 2,5" SATA-SSD
Omvandlar i stort sett alla 2,5 tums SATA- och SAS-hårddiskar till en 3,5 tums SATA-hårddisk
Provides safe handling and anti-static protection for most 2.5in hard drives
Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet
Provides safe handling and anti-static protection for most 2.5in hard drives
Provides safe handling and anti-static protection for most 2.5in hard drives
Skydda en 3,5" hårddisk mot elstötar/sammanstötningar
Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:
Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.
The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.
Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.
Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.
After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:
The primary partition on the drive now uses the entire drive area.
StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode . A duplication that fails or halts will not cause a problem with the source drive.
StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.
If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.
Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.
Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.
StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.
SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.
To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.