Produkt ID: SDOCK1EU3P
Få ut det mesta ur dina SATA-enheter. Denna fristående raderings-dockningsstation låter dig radera dina 2,5" och 3,5" solid state-enheter eller hårddiskar utan att ansluta till en värddator så att det är enkelt att få ny användning av din SATA-enhet. För extra sinnesro skriver dockningsstationen ut en bekräftelse när data har raderats säkert.
Raderings-dockningsstationen är dessutom en dockningsstation med ett fack för din SATA-enhet med snabb USB 3.0-prestanda, även känd som USB 3.1 Gen 1 (5 Gbps).
Med industri-erkända raderingslägen kan du vara säker på att den fristående raderaren säkert rensar, raderar eller sanerar data från din 2,5" eller 3,5" SSD eller HDD.
Hårddiskrensaren stöder nio rensningslägen, inklusive Quick Erase, Single and Multi-pass Overwrites, Custom Erase, Secure Erase och Enhanced Secure Erase. Raderingsproceduren multi-pass-överskrivning (3-pass överskrivning av hela enheten) möter kraven på DoD-standarder (5220.22-M).
Med raderings-dockningsstationen kan du ansluta till en RS232 seriell skrivare för att skriva ut en rapport över raderingsproceduren och bekräfta att raderingen har lyckats. Denna funktion är idealisk för IT-tekniker, systemadministratörer eller andra avdelningar som behöver bekräftelse vid radering av känslig eller konfidentiell information. Som referens visar kvittot tydligt tid och datum för raderingen samt vilket raderingsläge som använts.Denna hårddiskraderare säkerställer att data rensas (säkert radering), vilket krävs av myndigheter och organisationer med strikta riktlinjer för borttagning av data. Wipe är en mycket säker metod för att radera data från din lagringsenhet och den uppfyller NIST 800-88 Rev. 1 media sanitetsstandard som fastställts av National Institute of Standards and Technology.
För IT-tekniker eller proffs som behöver kontrollera filer eller testa olika hårddiskar eftersom dockningsstationen låter dig hot-swap:a enheter vid behov. Dockningsstationen har ett SATA-fack med toppmatning för enkel åtkomst till din enhet, vilket gör det enkelt att snabbt säkerhetskopiera eller föra över data till en hårddisk eller solid state-enhet.
Med sitt stöd för SATA I och II och enheter med hög kapacitet (testad med upp till 6 TB) är denna dockningsstation kompatibel med i stort sett vilken 2,5-tums och 3,5-tums SATA SSD eller HDD som helst.
Raderings-dockningsstationen fungerar dessutom med mSATA-enheter och M.2-enheter med hjälp av en kompatibel adapter från StarTech.com:
mSATA-hårddiskar: Använd StarTech.coms adapter SAT32MSAT257 mSATA SSD till 2,5 tums SATA-adapter-konverterare
M.2-hårddiskar: Använd StarTech.coms adapter SAT32M225 M.2 NGFF SSD till 2,5 tums SATA-adapter-konverterare
Raderings-dockningsstationen är OS-oberoende vilket garanterar snabb och enkel installation. Den kompakta designen och lilla storleken gör att den enkelt får plats på arbetsytan.
Den TAA-kompatibla SDOCK1EU3P täcks av StarTech.com:s 2-årsgaranti och gratis livstidsgaranti på teknisk support.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Package Height | 91 mm [3,6 in] |
Package Length | 37,6 cm [14,8 in] | |
Fraktvikt (förpackning) | 2,0 kg [4,5 lb] | |
Package Width | 18,9 cm [7,4 in] | |
Hårdvara | Gränssnitt | USB 3.0 |
Busstyp | USB 3.0 | |
Antal enheter | 2 | |
Enhetsstorlek | 2.5in & 3.5in | |
Enhetstyp | SATA | |
Indikatorer | 1 - LED-indikatorer | LCD-display med 2 rader på ovansidan |
LED för ström&aktivitet | ||
LED för HPA/DCO-identifiering | ||
Kontakt(er) | 2 - Enhetskontakter | SATA data- & ström-kombo (7+15-stifts) |
1 - Värdkontakter | USB Type-B (9-stifts) USB 3.0 | |
1 - Övriga gränssnitt | DB 9-pin Serial | |
Miljö | Drifttemperatur | 0°C to 40°C (32°F to 104°F) |
Förvaringstemperatur | -10°C to 65°C (14°F to 149°F) | |
Luftfuktighet | 10% ~ 90% RH | |
Mjukvara | OS-kompatibilitet | OS independent; No software or drivers required |
Prestanda | Maximal dataöverföringshastighet | 3 Gbps |
Typ och hastighet | USB 3.0 - 5 Gbit/s | |
SATA II (3 Gbps) | ||
Raderingslägen | Quick Erase | |
Maximal enhetskapacitet | För närvarande testad med upp till 6 TB 7200 RPM | |
Raderingslägen | 1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear) | |
Hot swap-förmåga | Ja | |
Raderingslägen | 3-Pass Overwrite | |
7-Pass Overwrite | ||
Custom Erase | ||
Secure Erase (NIST SP 800-88 Rev 1 - Purge) | ||
Enhanced Secure Erase (NIST SP 800-88 Rev 1 - Purge) | ||
Ström | Power Source | AC-adapter medföljer |
Inspänning | 100 - 240 AC | |
Inström | 1.4 A | |
Utspänning | 12V DC | |
Utström | 5 A | |
Strömförbrukning | 60 | |
Särskilda anmärkningar/krav | Obs. | Kvittoutskrift genom den seriella RS232-porten kräver en skrivare med stöd för ESC/P-skrivarkontrollspråk. |
Utseende | Färg | Svart |
Kabinettyp | Av plast | |
Produktlängd | 14 cm [5,5 in] | |
Produktbredd | 12,3 cm [4,8 in] | |
Produkthöjd | 70 mm [2,8 in] | |
Produktvikt | 656 g [23,2 oz] | |
Vad det är i lådan | 1 - Ingår i paketet | hårddiskraderare och USB 3.0-dockningsstation |
USB 3.0-kabel | ||
Universell strömadapter | ||
4 - Ingår i paketet | strömadapter-kontakt (NA/EU/UK/AU) | |
1 - Ingår i paketet | Snabbstartsguide |
Konvertera en M.2 SSD till en 7 mm hög 2,5" SATA-SSD 6 Gbps med öppen ram
Konvertera en mSATA-SSD till en 7 mm hög 2,5" SATA-SSD på 6 Gbps med öppen ram
Provide protection against shocks/impacts to a 2.5in hard drive
Skydda en 3,5" hårddisk mot elstötar/sammanstötningar
Provides safe handling and anti-static protection for most 2.5in hard drives
Provides safe handling and anti-static protection for most 2.5in hard drives
Provides safe handling and anti-static protection for most 2.5in hard drives
Provides safe handling and anti-static protection for most 2.5in hard drives
Provides safe handling and anti-static protection for most 2.5in hard drives
Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet
Connect to your external solutions and transfer data at 10x the speed of USB 2.0
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time.
The power and link LED on the hard drive eraser dock is illuminated while the drive is being erased. When the process is complete, the yellow LED is no longer illuminated.
The suggested time that the erase process will take is a conservative estimate based on the characteristics of the individual hard drive, including the maximum read and write speeds and overall health of the hard drive. The erase mode that you select can also impact the time it takes to erase the drive, as the more in-depth erase modes require more resources.
To connect your SDOCK1EU3P to your serial printer, use the same type of serial cable (straight-through or null modem) that you used to connect your serial printer to your computer. If you aren't sure which cable to use to connect your serial printer to your computer, consult the website of the serial printer manufacturer.
Du bör inte uppgradera enhetens inbyggda programvara om du inte har några problem med enhetens funktioner. Du behöver bara uppgradera om du har problem med enheten och är säker på att problemet är den inbyggda programvaran. Du kan bekräfta detta genom att läsa igenom den medföljande dokumentationen eller kontakta vår tekniska avdelning. Felaktig uppgradering av inbyggd programvara kan resultera i minskade prestanda så vi rekommenderar att du kontaktar StarTech.com först.
The suggested time that the erase process will take is a conservative estimate based on the characteristics of the individual hard drive, including the maximum read and write speeds and overall health of the hard drive. The erase mode that you select can also impact the time it takes to erase the drive, as the more in-depth erase modes require more resources.
To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.