Fiber Optic Cable - Multimode Duplex 50/125 - LSZH - LC/ST - 5 m

Connect fiber network devices for high-speed transfers with LSZH rated cable

Produkt ID: 50FIBLCST5

  • 1x LC MM male connector
  • 1x ST MM male connector
  • OM2 (50/125) 500MHz multimode fiber
Ditt pris
€17,99 EUR excl. VAT
€22,49 EUR incl. VAT

The 50FIBLCST5 5m LSZH LC to ST Fiber Cable features 50/125 micron fiber for high-speed, high bandwidth data transmissions over Gigabit Ethernet and Fiber Channel networks, with support for duplex multimode applications.

This LC-ST patch cable is housed in a LSZH (Low-Smoke, Zero-Halogen) flame retardant jacket, to ensure minimal smoke, toxicity and corrosion when exposed to high sources of heat, in the event of a fire. Making it ideal for use in industrial settings, central offices and schools, as well as residential settings where building codes are a consideration.

Each Duplex 50/125 (OM2) Multimode Fiber Patch Cable is individually tested and certified to be within acceptable optical insertion loss limits for guaranteed compatibility and 100% reliability and is backed by our lifetime warranty.

Användning

  • Use in Gigabit Ethernet and Fiber Channel applications
  • Ideal solution for data applications requiring high speed data transmission
  • Broadband systems
  • Telecommunication/Data communication

Fördelarna med StarTech.com

  • LSZH-rated cable, suitable for installations under restrictive building codes
  • High-speed, high bandwidth transmissions over Gigabit Ethernet/fiber channel networks
  • Resistant to pulls, strains, and impacts during your cable installations and maintenance

Partnernummer

  • Ingram Micro Sweden V932274
  • UPC 065030849746

Specifikationer

Warranty Information Warranty Lifetime
Förpackning Package Height 20 mm [0,8 in]
Package Length 22 cm [8,7 in]
Package Width 20 cm [7,9 in]
Förpackningsantal 1
Fraktvikt (förpackning) 85 g [3,0 oz]
Hårdvara Brandteknisk klass LSZH-klassad (Low Smoke Zero Halogen)
Fiberstorlek 50/125
Kontakt(er) 1 - Connector A Fiberoptisk LC duplex
1 - Connector B Fiberoptisk ST duplex
Miljö Luftfuktighet 0~90% RH
Drifttemperatur -20°C to 60°C (-4°F to 140°F)
Förvaringstemperatur -20°C to 60°C (-4°F to 140°F)
Prestanda Maximal dataöverföringshastighet 10Gbps
Kabelklassificering 1Gbps / 10Gbps
Fiberklassificering OM2
Fibertyp Multiläge
Utseende Färg Orange
Kabellängd 5 m [16,4 ft]
Produktlängd 5 m [16,4 ft]
Produktvikt 76 g [2,7 oz]
Vad det är i lådan 1 - Ingår i paketet 5m Multimode 50/125 Duplex Fiber Patch Cable LC – ST

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a network cable, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Network devices

  • Network cables

To test your setup components, try the following:

  • Use the network devices and network cables in another setup to see if the problem is with the components or the setup.

  • Use different network devices and network cables in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the network devices and network cables, make sure that the link LEDs (if present) turn on for both of the devices. This indicates basic network connectivity between the network devices. You also need to determine if your devices need a straight through or a crossover cable. For more information about straight through and crossover cables, see the following FAQ: http://www.startech.com/faq/network_cables_straight_through_vs_crossover

If the link LEDs are not illuminated or there are not any LEDs present, you will need to troubleshoot your devices. Alternatively, you can also use a network cable tester, such as the or .

Before You Buy

Different optical cables are needed for different applications. Before you select a cable to interconnect fiber devices, make sure that the following things match:

  • Mode: Single Mode or Multi Mode.

  • Wavelength: For example, 850 nm, 1310 nm, or 1550 nm.

Note: The above properties cannot be converted or changed by a cable.

When you select a cable, make sure that the cable ends (for example, LC, SC, ST, or MT) match the fiber media devices.

Simplex and duplex ends are available for most connector types. Simplex cables have the connectors separate, where duplex cables have the transmit (TX) and receive (RX) connectors joined together.  StarTech.com fiber media devices are compatible with simplex and duplex connectors.

It does not matter which diameter or OM classification the cable uses, as long as it meets the mode requirement.

Fiber media converters can be used to convert a standard Ethernet connection to a standard fiber connection, or can be used to extend a copper Ethernet network. When you use fiber media converters to extend a copper Ethernet network, make sure that the same fiber standards are being used on either end of the fiber network.

UPC and APC are fiber cable connector types. UPC (Ultra Physical Contact) connectors have a fiber connector end face that has been polished to be dome-shaped. This results in light that can be reflected straight back to the source.

APC (Angled Physical Contact) connectors have a fiber connector end face that has been polished at an eight degree angle. This results in a reduced amount of light that is reflected between the two connected fibers.

StarTech.com fiber cables use UPC connectors.

Compliance and safety

Compliance letters

  • WEEE
    • Språk: English
  • RoHS
    • Språk: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen