Utgått

PCI SATA RAID-kontrollerkortadapter med 4 portar

Lägg till 4 SATA-portar till din PC via en utbyggnadskortplats för PCI som stödjer högpresterande RAID-array installation

Produkt ID: PCISATA4R1

  • 4 interna SATA-portar
  • Stöd för JBOD, RAID 0 (skiktning), RAID 1 (spegling), RAID 0+1 (skikt + spegel) och RAID 1+Reserv
  • Stöd för enheter med stort utrymme med 48-bit LBA (Logical Block Addressing)

PCISATA4R1 PCI SATA RAID-kontroller med 4 portar gör det möjligt att lägga till fyra interna SATA 1.0-portar (1,5 GBPS) till din PC-dator genom en enda PCI-utbyggnadskortplats. Samtidigt har den också stöd för flera RAID-lägen eller en enkel JBOD-konfiguration (Just a Bunch of Disks).

PCI SATA-kortet ger utökad prestanda och kapacitet med RAID 0 (skiktning) eller överflödig kopia på din hårddisk med RAID 1 (spegling). Att konfigurera i RAID 10 (även känd som RAID 0+1) gör att du kan skapa en speglad kopia av din skiktade disksats. SATA RAID-kortet stödjer dessutom RAID 1+S (Spegel + Reserv) vilket använder en tredje installerad enhet för att automatiskt ersätta den fallerade enheten och för att bygga om den speglade satsen – även om det är startenheten som har fallerat.

För att kunna passa de flesta standardchassin, levereras kortet med ett standardprofilfäste installerat och inkluderar ett lågprofilsfäste för att kunna anpassa till kompakta system eller system med liten formfaktor.

OBS: Samtidigt som PCISATA4R1-kortet stödjer alla hårddiskstorlekar i JBOD-läge, är den stöttade hårddiskstorleken i RAID-läge 2 TB (per port).

Täcks av StarTech.coms livstidsgaranti och gratis livstidsgaranti på teknisk support. 

Användning

  • Expandera en äldre PCI-baserad PC-dator eller ett serversystem med ytterligare 4 SATA-portar
  • Lägg till flera SATA-portar till ett datorsystem med lågprofil/liten formfaktor (SFF)
  • Perfekt lösning för RAID-lagring med flera enheter

Fördelarna med StarTech.com

  • Konfigurera dataredundans, ökad kapacitet eller båda med mångsidig RAID support
  • Passar nästan alla PC-chassin och låg- och helprofilsfästen medföljer

Partnernummer

  • UPC 065030805162

Kompatibilitet

  • Windows 8 logo
  • Linux logo
  • Windows 7 logo
  • Windows Server 2012 logo
  • Windows 10 logo
  • Windows 11 logo
Windows® 2000, XP, Vista, 7, 8, 8.1, 10, 11
Windows Server® 2003, 2008 R2, 2012, 2012 R2
Linux 3.5 to 4.4.x LTS Versions only

Specifikationer

Warranty Information Warranty Lifetime
Förpackning Package Length 21,7 cm [8,5 in]
Package Width 48 mm [1,9 in]
Package Height 16 cm [6,3 in]
Fraktvikt (förpackning) 0,2 kg [0,4 lb]
Hårdvara Portar 4
Gränssnitt SATA
Busstyp PCI / PCI-X (5 / 3.3V)
Korttyp Standardprofil (inkl. LP-fäste)
Chipset-ID Silicon Image - SiI3114R
Kontakt(er) 1 - Kontakttyp(er) PCI/PCI-X (universell 3,3 & 5 V, 32-bitars)
4 - Interna portar SATA (7-stifts, data)
Miljö Drifttemperatur 5°C to 50°C (41°F to 122°F)
Förvaringstemperatur -25°C to 70°C (-14°F to 158°F)
Luftfuktighet 15% ~ 90% RH
Mjukvara OS-kompatibilitet Windows® 2000, XP, Vista, 7, 8, 8.1, 10, 11
Windows Server® 2003, 2008 R2, 2012, 2012 R2
Linux 3.5 to 4.4.x LTS Versions only
Prestanda Maximal dataöverföringshastighet 1,5 Gbps
FIFO 256 Bytes per channel
Typ och hastighet SATA I (1.5 Gbps)
Port Multiplier Nej
LBA-stöd 48-bit
RAID Ja
RAID-lägen som stöds RAID 10 (1+0, Stripat set av speglade enheter)
KLONING (RAID 1 + extra)
JBOD - (Just a Bunch of Disks)
RAID 1 (speglade enheter)
RAID 0 (stripade enheter)
Särskilda anmärkningar/krav Obs. Samtidigt som PCISATA4R1-kortet stödjer alla hårddiskstorlekar i JBOD-läge, är den stöttade hårddiskstorleken i RAID-läge 2 TB (per port).
Utseende Produktlängd 12 cm [4,7 in]
Produktbredd 45 mm [1,8 in]
Produkthöjd 2,2 cm [0,9 in]
Produktvikt 46 g [1,6 oz]
Vad det är i lådan 1 - Ingår i paketet PCI SATA-kort
Lågprofilsfäste
Installationsskiva
Instruktionsbok

Tillbehör

SATA18

45 cm SATA seriell ATA-kabel

Denna högkvalitativa SATA-kabel är framtagen för att kunna ansluta SATA-enheter även i trånga utrymmen.

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
SATA24

60 cm SATA seriell ATA-kabel

Denna högkvalitativa SATA-kabel är framtagen för att kunna ansluta SATA-enheter även i trånga utrymmen.

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
SATA36

36in SATA Serial ATA Cable

Connect and position SATA drives easily - designed for larger cases

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
SATA18POW

18in SATA Serial ATA Data and Power Combo Cable

Power your Internal SATA hard drive from an LP4 connector on your Power Supply

Ditt pris
€6,99 EUR excl. VAT
€8,74 EUR incl. VAT
SATA18RA1

45 cm SATA till högervinklad SATA seriell ATA-kabel

Anslut din SATA-enhet i rät vinkel vid installation i trånga utrymmen

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
SATA24RA1

24in SATA to Right Angle SATA Serial ATA Cable

Make a right-angled connection to your SATA drive, for installation in tight spaces

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
SATA36RA1

36in SATA to Right Angle SATA Serial ATA Cable

Make a right-angled connection to your SATA drive, for installation in tight spaces

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
Utgått
SATARA24

24in Right Angle SATA Cable

Make a right-angled connection to your SATA drive, for installation in tight spaces

Ditt pris
€1,99 EUR excl. VAT
€2,49 EUR incl. VAT
SATARA36

36in Right Angle SATA Cable

Make a right-angled connection to your SATA drive, for installation in tight spaces

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Drivrutin(er):

Manual(er):

Mjukvara

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables

  • Hard drives

  • Hard drive controller card

To test your setup components, try the following:

  • Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.

  • Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the hard drive and hard drive controller card, it is recommended that you do the following:

  1. To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.

  2. Do one of the following:

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.

  2. If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.

In order to rebuild a RAID array, you need to replace a physical drive with an identical drive on the same RAID controller. Although standard RAID levels are generally agreed upon throughout the industry, the implementation varies between manufacturers. RAID arrays are typically not accessible when they are moved to another controller, and data may be unrecoverable if the drives are out of order or have been formatted or accessed by another RAID controller.

If a RAID controller has failed, you should get the exact same model of RAID controller.  

Note: If a drive or drives were damaged, it is possible that the RAID array may be permanently unrecoverable.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, you should back up the data on another physical drive or logical set of drives.

Rebuild a RAID array

With the following RAID modes, recovery is possible using the same StarTech.com product. Refer to the following table for the appropriate method to use to recover your RAID array.

RAID mode Max # of failed drives Procedure
RAID 1 Only one drive is needed for recovery.
  1. Determine which drive is operational by using the RAID management utility (if available) or test each drive individually on a different hard drive controller (for example, a hard drive docking station or SATA controller).

  2. Replace the failed drive with an identical hard drive.

The array will rebuild and is accessible during the rebuilding process.

RAID 3 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 5 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 10 Only one drive in a mirrored set can fail.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

 

Hur man

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

In order to use a hard drive plugged into a hard drive controller card as your operating system, you need to install the operating system onto the hard drive while it is plugged into the expansion card. To do this, complete the following:

Note: Not all hard drive controller cards have drivers that allow you to install the operating system onto the hard drive. All of the hard drive controllers that display this FAQ include this capability.

Before you begin, consult the documentation that came with the motherboard to make sure that the motherboard or BIOS supports booting from an expansion card.

  1. Back up any data on the hard drive.
  2. Make a copy of the drivers from the website onto a floppy disc, CD, DVD, or USB flash drive. The drivers that you download depends on the operating system that you want to install.
  3. Install the hard drive controller card onto your motherboard.
  4. Plug the hard drive into the controller card.
  5. Turn on your computer and open the operating system install wizard.
  6. Before you select the hard drive that you want to install the operating system onto, select the option to install third-party drivers.
  7. Point the driver installer to the floppy disc, CD, DVD, or USB flash drive.
  8. Install the drivers.
  9. Select the hard drive on the hard drive controller card as the location where you want to install the operating system.
  10. Complete the on-screen instructions to finish installing the operating system.

Before You Buy

Although you can adapt a Serial Attached SCSI (SAS) drive to connect to a standard SATA controller card, the card must support SAS commands in order to communicate with SAS drives. SAS drives have a different command set that is not present on SATA controllers.

This SATA controller card only supports standard SATA drives.

This device does not support the ATA Packet Interface (ATAPI) protocol. ATAPI is required for optical drives, including CD-ROM drives, DVD-ROM drives, and Blu-ray players. Because this device does not support ATAPI, optical drives are also not supported over any IDE, SATA, or eSATA connections.

For a list of products that do support ATAPI, refer to the following FAQ: https://www.startech.com/faq/hard_drive_controllers_atapi_support.

Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.

Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.

The following are terms that are normally used in connection with RAID:

  • Striping: data is split between multiple disks.
  • Mirroring: data is mirrored between multiple disks.
  • Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.

Different RAID levels exist for different application requirements.

Refer to the following table for the list of RAID modes offered by some StarTech.com products:

RAID mode Description Operation Advantages Disadvantages Recovery
RAID 0 Striped disks Data is split evenly between two or more disks. Large size and the fastest speed. No redundancy. If one or more drives fails, this results in array failure.
RAID 1 Mirrored disks Two or more drives have identical data on them. A single drive failure will not result in data loss. Speed and size is limited by the slowest and smallest disk. Only one drive is needed for recovery.
RAID 3 Striped set with dedicated parity Data is split evenly between two or more disks, plus a dedicated drive for parity storage. High speeds for sequential read/write operations. Poor performance for multiple simultaneous instructions. A single drive failure will rebuild.
RAID 5 Striped disks with distributed parity Data is split evenly between three or more disks. Parity is split between disks. Large size, fast speed, and redundancy. The total array size is reduced by parity. A single drive failure will rebuild.
RAID 10 1+0; Striped set of Mirrored Subset Four or more drives are made into two mirrors that are striped. Larger size and higher speed than RAID-1, and more redundancy than RAID-0. No parity. Only one drive in a mirrored set can fail.
JBOD Just a Bunch Of Disks Any number of drives are accessed independently by the operating system. Software RAID modes can be used. Hardware RAID may have better performance. N/A
Big Spanning or Concatenation Data is written on one drive until it is full, and then the next drive(s) until it or they are full. Creates a very large and simple array.

No redundancy.

N/A
Clone RAID 1 + Spare

Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure.

Seamless operation when one drive fails in a RAID-1 array. Spare drive is not accessible to the user. Only one drive is needed for recovery.

 

Yes. This PCI card uses a universal connector keyed for both 3.3V and 5V that can be used with PCI and PCI-X. This type of connector is identified as having 2 separate notches, instead of just one.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen